06-17-2009 08:13 AM - edited 03-15-2019 06:34 PM
Hi, I want connect a E1 to a router 2851 with CUCME 4.1, but whenever I dial some DID (after configure the card VWIC2-2MFT-T1/E1), the calls are not routed to the extensions, the first thing the router do is give me a tone of reorder to dial the extension and then the call is routed to the extension
Solved! Go to Solution.
06-17-2009 10:07 AM
conf t
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
Noete you can group the analog ports under trunk group, that will allow you to collapse most DPs under a single one.
06-17-2009 08:42 AM
Do you have more than one Pots dial-peers configured?
If so ensure you have incoming called-number. & direct-inward-dial on the dial-peer you expect inbound calls to use.
06-17-2009 09:59 AM
06-17-2009 10:07 AM
conf t
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
Noete you can group the analog ports under trunk group, that will allow you to collapse most DPs under a single one.
06-17-2009 10:15 AM
ok, i will try this, and after I tell you the result, thanks
06-22-2009 07:51 AM
Hi, me again.
the problem to receive calls, was solved (thank's for yours councils), but I have a new problem.
Now, I can not make calls to PSTN from PBX. PBX are a Panasonic 1232 with E1 card
06-22-2009 07:55 AM
Need to see configuration. Do not send full configuration, only voice related, do not use attachments if possible.
Please remember to rate useful posts with the scrollbox below.
06-22-2009 08:10 AM
This the configuration
----------------------
controller E1 0/2/0
framing NO-CRC4
ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani
cas-custom 0
country telmex
category 2
answer-signal group-b 1
caller-digits 4
dnis-digits min 4 max 4
ani-digits min 0 max 20
dnis-complete
description TRONCALES DIGITALES AXTEL
!
controller E1 0/2/1
framing NO-CRC4
clock source internal
ds0-group 0 timeslots 1-15,17-20 type r2-digital r2-compelled ani
cas-custom 0
country telmex use-defaults
category 2
answer-signal group-b 1
timer interdigit incoming 2500
dtmf timer inter-digit 2500
description TRONCALES PANASONIC
!
!
voice-port 0/2/0:0
cptone MX
!
voice-port 0/2/1:0
cptone MX
timeouts interdigit 3
timing digit 400
!
dial-peer voice 1 pots
incoming called-number 55508916..
direct-inward-dial
port 0/2/0:0
!
dial-peer voice 2 pots
description PBX
destination-pattern 16..
direct-inward-dial
port 0/2/1:0
forward-digits all
!
dial-peer voice 3 pots
corlist outgoing ll-loc
description LLAMADAS LOCAL
destination-pattern 9........
direct-inward-dial
telephony-service
service dnis overlay
user-locale ES
network-locale ES
time-zone 9
time-format 24
date-format yy-mm-dd
dialplan-pattern 1 55508916.. extension-length 4 extension-pattern 14..
max-conferences 2 gain -6
moh twenty.au
transfer-system full-consult
--------
thanks
06-22-2009 08:14 AM
Is the E1 to PBX up ? Check show controllers E1.
Is the PBX ready to receive 4 digits beginning with 16 ?
If yes to both questions, take "debug vpm signal" with "term mon" whe dialing 16xx.
06-22-2009 09:39 AM
Sorry, I think not explain me good
When I try make a call to outside, the router give me dial tone, however if I dial any digit sequence, router only catch first digit and ignore the rest of digits
06-22-2009 10:37 AM
Explain which calls work, and which ones do not. Check controllers also.
06-22-2009 01:38 PM
One more time, s
orry, my english is not very well
I try connect the PBX (Panasonic 1232) to a router Cisco 2851 (with CCME 4.1) using card VWIC2-2MFT-T1/E1.
Incoming calls (Router to PBX) are completed succesful, but outgoing calls (PBX to Router) are not completed.
When I try make a call (from PBX), I hear dial tone and saw with the "show voice call summary" command that one line is goes off hook, then I start press digit, only the first digit is understand, the other digits are showed incorrectly (example 4#, or #) so the call is not complete.
What does you mean with check controllers, I don't understand???
I attach the debug file
07-07-2009 09:33 AM
This is ended
I configure the route of the calls to the interface appropriate. Thanks for your help
08-14-2009 10:04 AM
Hello there. I have a similar issue. Could you post the commands you used to solve you issue ?
Regards
08-14-2009 10:52 AM
Please open new thread for a new problem, describe the problem in detail and include the relevant configuration.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide