Solved: About SFP on C7606

j.han · ‎06-19-2009

Hi Netpro:

here is my question:system prompt monitoring disabled for all interface, what's its meaning,the output is fake ?

thanks all

show int g5/1 tran detail Transceiver monitoring is disabled for all interfaces.

ITU Channel not available (Wavelength not available), Transceiver is externally calibrated.

cisco_lad2004 · ‎06-19-2009

Jun,

This is normal, you need to enable Digital Optical Monitoring or DOM. Then you would be able to see Laser budget and other transceiver data.

sh int te1/4 transceiver detail

Transceiver monitoring is disabled for all interfaces. <<=== When DOM is enabled it does overwrite snmp traps for transceiver.

ITU Channel not available (Wavelength not available),

Transceiver is internally calibrated.

mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.

++ : high alarm, + : high warning, - : low warning, -- : low alarm.

A2D readouts (if they differ), are reported in parentheses.

The threshold values are calibrated.

High Alarm High Warn Low Warn Low Alarm

Temperature Threshold Threshold Threshold Threshold

Port (Celsius) (Celsius) (Celsius) (Celsius) (Celsius)

------- ------------------ ---------- --------- --------- ---------

Te1/4 30.8 75.0 70.0 0.0 -5.0

High Alarm High Warn Low Warn Low Alarm

Voltage Threshold Threshold Threshold Threshold

Port (Volts) (Volts) (Volts) (Volts) (Volts)

------- --------------- ---------- --------- --------- ---------

Te1/4 0.00 0.00 0.00 0.00 0.00

High Alarm High Warn Low Warn Low Alarm

Current Threshold Threshold Threshold Threshold

Port (milliamperes) (mA) (mA) (mA) (mA)

------- ----------------- ---------- --------- --------- ---------

Te1/4 6.5 17.0 14.1 2.0 2.0

Optical High Alarm High Warn Low Warn Low Alarm

Transmit Power Threshold Threshold Threshold Threshold

Port (dBm) (dBm) (dBm) (dBm) (dBm)

------- ----------------- ---------- --------- --------- ---------

Te1/4 -0.3 3.5 2.5 -10.2 -11.2

Optical High Alarm High Warn Low Warn Low Alarm

Receive Power Threshold Threshold Threshold Threshold

Port (dBm) (dBm) (dBm) (dBm) (dBm)

------- ----------------- ---------- --------- --------- ---------

Te1/4 -0.3 2.5 1.5 -15.4 -16.4

How to configure DOM ? on 7600, I use "Transceiver type all"

Not all modules are DOM capable, see compatibility here:

http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_8031.html

HTH

Sam

View solution in original post

Giuseppe Larosa · ‎06-19-2009

Hello Jianghui,

but

sh int gi5/1 status what tells ?

is the port used and usable or you have troubles with it ?

May you provide a sh module and IOS image name?

All this in order to get better help you may be hitting a SW bug for example.

Hope to help

Giuseppe

j.han · ‎06-19-2009

Hi Giuseppe:

it's your needed information:

the port is in used and no admin shutdown,actually I don't think it's Image bug .

thanks your response

total output :

#show int Gi5/1 transceiver Transceiver monitoring is disabled for all interfaces.

ITU Channel not available (Wavelength not available), Transceiver is externally calibrated.

If device is externally calibrated, only calibrated values are printed.

++ : high alarm, + : high warning, - : low warning, -- : low alarm.

NA or N/A: not applicable, Tx: transmit, Rx: receive.

mA: milliamperes, dBm: decibels (milliwatts).

Optical Optical

Temperature Voltage Current Tx Power Rx Power

Port (Celsius) (Volts) (mA) (dBm) (dBm)

------- ----------- ------- -------- -------- --------

Gi5/1 24.3 3.26 9.5 -- 3.9 -40.0 --

#sh ver

Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB4, RELEASE SOFTWARE (fc3)

Last reset from power-on

1 SIP-400 controller (2 GigabitEthernet)(1 POS).

1 Virtual Ethernet interface

4 Gigabit Ethernet interfaces

1 Packet over SONET interface

3964K bytes of non-volatile configuration memory.

#sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 0 4-subslot SPA Interface Processor-400 7600-SIP-400

5 2 Route Switch Processor 720 (Active) RSP720-3C-GE

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0024.14c8.b2c0 to 0024.14c8.b33f 2.6 12.2(33)SRB4 12.2(33)SRB4 Ok

5 001d.4559.3000 to 001d.4559.3003 5.7 12.2(33r)SRC 12.2(33)SRB4 Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

1/0 1xOC12 POS SPA SPA-1XOC12-POS 1.0 Ok

1/1 2xGE V2 SPA SPA-2X1GE-V2 1.0 Ok

5 Policy Feature Card 3 7600-PFC3C 1.1 Ok

5 C7600 MSFC4 Daughterboard 7600-MSFC4 1.1 Ok

Mod Online Diag Status

---- -------------------

1 Pass

1/0 Pass

1/1 Not Applicable

5 Pass

cisco_lad2004 · ‎06-19-2009

Jun,

This is normal, you need to enable Digital Optical Monitoring or DOM. Then you would be able to see Laser budget and other transceiver data.

sh int te1/4 transceiver detail

Transceiver monitoring is disabled for all interfaces. <<=== When DOM is enabled it does overwrite snmp traps for transceiver.

ITU Channel not available (Wavelength not available),

Transceiver is internally calibrated.

mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.

++ : high alarm, + : high warning, - : low warning, -- : low alarm.

A2D readouts (if they differ), are reported in parentheses.

The threshold values are calibrated.

High Alarm High Warn Low Warn Low Alarm

Temperature Threshold Threshold Threshold Threshold

Port (Celsius) (Celsius) (Celsius) (Celsius) (Celsius)

------- ------------------ ---------- --------- --------- ---------

Te1/4 30.8 75.0 70.0 0.0 -5.0

High Alarm High Warn Low Warn Low Alarm

Voltage Threshold Threshold Threshold Threshold

Port (Volts) (Volts) (Volts) (Volts) (Volts)

------- --------------- ---------- --------- --------- ---------

Te1/4 0.00 0.00 0.00 0.00 0.00

High Alarm High Warn Low Warn Low Alarm

Current Threshold Threshold Threshold Threshold

Port (milliamperes) (mA) (mA) (mA) (mA)

------- ----------------- ---------- --------- --------- ---------

Te1/4 6.5 17.0 14.1 2.0 2.0

Optical High Alarm High Warn Low Warn Low Alarm

Transmit Power Threshold Threshold Threshold Threshold

Port (dBm) (dBm) (dBm) (dBm) (dBm)

------- ----------------- ---------- --------- --------- ---------

Te1/4 -0.3 3.5 2.5 -10.2 -11.2

Optical High Alarm High Warn Low Warn Low Alarm

Receive Power Threshold Threshold Threshold Threshold

Port (dBm) (dBm) (dBm) (dBm) (dBm)

------- ----------------- ---------- --------- --------- ---------

Te1/4 -0.3 2.5 1.5 -15.4 -16.4

How to configure DOM ? on 7600, I use "Transceiver type all"

Not all modules are DOM capable, see compatibility here:

http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_8031.html

HTH

Sam