ES+ 40 card (7606)

Answered Question
Jul 9th, 2009

1 port on the ES 40 card has both LED on.

documentation says:

Green and Amber On: Undefined condition.

what is that mean, good, bad ? don't use

thanks

I have this problem too.
0 votes
Correct Answer by Jerry Ye about 7 years 5 months ago

Hi Atif,

Have you tried to swap SFP to 2/1? Change it and run the diag again. If problem presist, I think you might have an HW issue.

Regards,

jerry

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4.5 (2 ratings)
Loading.
Jerry Ye Thu, 07/09/2009 - 07:28

Hi Atif,

What is your version of IOS are you running? Can you post the output of show version and show module.

Regards,

jerry

Atif Siddiqui Thu, 07/09/2009 - 07:31

only 1 port out of 40 is showing this message:

here it is.

PE4#sh ver

Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRD1, RELEASE SOFTWARE (fc4)

Technical Support: http://www.cisco.com/techsupport

PE4#sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

2 40 7600 ES+ 7600-ES+40G3CXL JAE1309493P

3 40 7600 ES+ 7600-ES+40G3CXL JAE1309493M

5 2 Route Switch Processor 720 (Active) RSP720-3C-GE JAE12024CGH

6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE JAE1130RD6Z

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

2 0024.f94c.0bc0 to 0024.f94c.0c1f 1.0 12.2(33r)SRD 12.2(33)SRD1 Ok

3 0024.f94c.0fd0 to 0024.f94c.102f 1.0 12.2(33r)SRD 12.2(33)SRD1 Ok

5 001b.d401.6e40 to 001b.d401.6e43 5.2 12.2(33r)SRB 12.2(33)SRD1 Ok

6 0007.0e61.d8c0 to 0007.0e61.d8c3 5.2 12.2(33r)SRB 12.2(33)SRD1 Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

2 7600 ES+ DFC XL 7600-ES+3CXL JAE13094A08 1.0 Ok

2 7600 ES+ 40xGE SFP 7600-ES+40G JAE1309487B 1.0 Ok

3 7600 ES+ DFC XL 7600-ES+3CXL JAE13062AG2 1.0 Ok

3 7600 ES+ 40xGE SFP 7600-ES+40G JAE13094881 1.0 Ok

5 Policy Feature Card 3 7600-PFC3C JAE12035PJY 1.1 Ok

5 C7600 MSFC4 Daughterboard 7600-MSFC4 JAE12035FCF 1.1 Ok

6 Policy Feature Card 3 7600-PFC3C JAE1130RWR3 1.1 Ok

6 C7600 MSFC4 Daughterboard 7600-MSFC4 JAE1130RR38 1.1 Ok

Mod Online Diag Status

---- -------------------

2 Pass

3 Pass

5 Pass

6 Pass

Atif Siddiqui Thu, 07/09/2009 - 08:03

I cannot access the ablve link.

I tried this, it gives error:

PE4#diagnostic mode enter module 2

Diagnostic mode is not supported in this image

Atif Siddiqui Thu, 07/09/2009 - 08:16

it gives me this message:

PE4#diagnostic start module 2 test 5 port 1

Diagnostic[Module 2]: Running test(s) 5 may disrupt normal system operation

Do you want to continue? [no]: yes

PE4#

*Jul 9 16:12:42.747: %DIAG-SP-6-TEST_RUNNING: Module 2: Running TestTransceiverIntegrity{ID=5} ...

PE4#

*Jul 9 16:12:42.747: %DIAG-SP-3-TEST_SKIPPED: Module 2: TestTransceiverIntegrity{ID=5} is skipped

on detail:

E4#show diagnostic result module 2 detail

Current bootup diagnostic level: minimal

Module 2: 7600 ES+ SerialNo : JAE1309493P

Overall Diagnostic Result for Module 2 : PASS

Diagnostic level at card bootup: minimal

Test results: (. = Pass, F = Fail, U = Untested)

5) TestTransceiverIntegrity:

Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

----------------------------------------------------------------------------

. U U U U U U U U U . U U U U U U U U . U U U U

Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

----------------------------------------------------

U U U U U U U U U U U U U U U U

Error code ------------------> 3 (DIAG_SKIPPED)

Total run count -------------> 0

Last test execution time ----> n/a

First test failure time -----> n/a

Last test failure time ------> n/a

Last test pass time ---------> n/a

Total failure count ---------> 0

Consecutive failure count ---> 0

Correct Answer
Jerry Ye Thu, 07/09/2009 - 08:51

Hi Atif,

Have you tried to swap SFP to 2/1? Change it and run the diag again. If problem presist, I think you might have an HW issue.

Regards,

jerry

Actions

This Discussion