07-13-2009 05:11 AM - edited 03-06-2019 06:44 AM
Hi,
I have a 2960 connected to a 3560 at 100/full. The port shows up w/ errors but I cannot ping the vlan on the 2960.
Auto mdix is on. Any thoughts?
Thanks
07-13-2009 05:18 AM
In addition, the 3560 port stat's showing a large amount of packets with errors. I already swapped out the cables but didnt help.
07-13-2009 07:14 AM
Sudip,
Multple VLAN's? Is trunking setup? Please provide a little more info.
sho run
sho int
sho int
sho int trunk
07-13-2009 12:10 PM
When I set Speed and Duplex to auto, the port status is UP (connects at 100/half). Any other combo (100/auto or auto/Full, etc) results in the port to be down.
Here is the sho int:
FastEthernet0/18 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0014.1cd8.0394 (bia 0014.1cd8.0394)
Description: CLTSW102 MGMT Connection
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, media type is 10/100BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:03, output hang never
Last clearing of "show interface" counters 04:13:13
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
11392 packets input, 837637 bytes, 0 no buffer
Received 10505 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 9317 multicast, 0 pause input
0 input packets with dribble condition detected
1072 packets output, 117964 bytes, 0 underruns
0 output errors, 0 collisions, 7 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Sho int vlan:
cltsw01#sho int trunk
Port Mode Encapsulation Status Native vlan
Gi0/1 on 802.1q trunking 1
Gi0/2 on 802.1q trunking 1
Gi0/3 on 802.1q trunking 1
Port Vlans allowed on trunk
Gi0/1 1-2,5,119
Gi0/2 1-2,5-6,119
Gi0/3 1-2,5
Port Vlans allowed and active in management domain
Gi0/1 1-2,5,119
Gi0/2 1-2,5-6,119
Gi0/3 1-2,5
Port Vlans in spanning tree forwarding state and not pruned
Gi0/1 1-2,5,119
Gi0/2 1-2,5-6,119
Gi0/3 1-2,5
07-13-2009 01:35 PM
The port will show down with anything other than auto for speed and duplex because you are using mdix which only works when the port is set as auto . If you want to hardcode the speeds and duplex then you will have to get a crossover cable to go to the other switch. If using mdix then set "both" ends as auto and it should negotiate ok .
07-13-2009 02:35 PM
This has been resolved. We did not specify the encapsulation type.
Thanks everyone.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide