07-13-2009 05:11 AM - edited 03-06-2019 06:44 AM
Hi,
I have a 2960 connected to a 3560 at 100/full. The port shows up w/ errors but I cannot ping the vlan on the 2960.
Auto mdix is on. Any thoughts?
Thanks
07-13-2009 05:18 AM
In addition, the 3560 port stat's showing a large amount of packets with errors. I already swapped out the cables but didnt help.
07-13-2009 07:14 AM
Sudip,
Multple VLAN's? Is trunking setup? Please provide a little more info.
sho run
sho int
sho int
sho int trunk
07-13-2009 12:10 PM
When I set Speed and Duplex to auto, the port status is UP (connects at 100/half). Any other combo (100/auto or auto/Full, etc) results in the port to be down.
Here is the sho int:
FastEthernet0/18 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0014.1cd8.0394 (bia 0014.1cd8.0394)
Description: CLTSW102 MGMT Connection
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, media type is 10/100BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:03, output hang never
Last clearing of "show interface" counters 04:13:13
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
11392 packets input, 837637 bytes, 0 no buffer
Received 10505 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 9317 multicast, 0 pause input
0 input packets with dribble condition detected
1072 packets output, 117964 bytes, 0 underruns
0 output errors, 0 collisions, 7 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Sho int vlan:
cltsw01#sho int trunk
Port Mode Encapsulation Status Native vlan
Gi0/1 on 802.1q trunking 1
Gi0/2 on 802.1q trunking 1
Gi0/3 on 802.1q trunking 1
Port Vlans allowed on trunk
Gi0/1 1-2,5,119
Gi0/2 1-2,5-6,119
Gi0/3 1-2,5
Port Vlans allowed and active in management domain
Gi0/1 1-2,5,119
Gi0/2 1-2,5-6,119
Gi0/3 1-2,5
Port Vlans in spanning tree forwarding state and not pruned
Gi0/1 1-2,5,119
Gi0/2 1-2,5-6,119
Gi0/3 1-2,5
07-13-2009 01:35 PM
The port will show down with anything other than auto for speed and duplex because you are using mdix which only works when the port is set as auto . If you want to hardcode the speeds and duplex then you will have to get a crossover cable to go to the other switch. If using mdix then set "both" ends as auto and it should negotiate ok .
07-13-2009 02:35 PM
This has been resolved. We did not specify the encapsulation type.
Thanks everyone.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: