Giuseppe Larosa Tue, 07/14/2009 - 05:56
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

Hello Kumar,


post

sh int g1/6


or sh port 1/6 (if catos)


it is good practice to provide some details in order to get help:

supervisor model operating system and version


Hope to help

Giuseppe


pselva2000 Tue, 07/14/2009 - 16:59
User Badges:

sorry for that


version is


interface GigabitEthernet1/6

switchport trunk encapsulation dot1q

switchport trunk native vlan 55

switchport mode trunk




Port Name Status Vlan Duplex

Gi1/6 inactive 1 full




Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M),

Version 12.2(31)SGA1, RELEASE SOFTWARE (fc3)


ROM: 12.2(25r)EW

Pod Revision 14, Force Revision 34, Tie Revision 29



System image file is "bootflash:cat4500-entservicesk9-mz.122-31.SGA1.bin"




Configuration register is 0x2




Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 6 Sup V-10GE 10GE (X2), 1000BaseX (SFP) WS-X4516-10GE JAB094301DM

2 6 Sup V-10GE 10GE (X2), 1000BaseX (SFP) WS-X4516-10GE JAB09160049

3 6 SFP, 10/100/1000BaseT (RJ45)V, Cisco/I WS-X4506-GB-T JAE1002TDW0




please let me know if any thing needed


vishwancc Wed, 07/15/2009 - 00:01
User Badges:

Hi Kumar,


I the Gig module detected by the SUP waht is the LED and show diag says ,have you tried in the other slot.


Chao

Vishwa

rtjensen4 Thu, 07/16/2009 - 10:14
User Badges:
  • Bronze, 100 points or more

I recently had a similar issue with my 4507R with Sup IV.

In my case, both supervisors have two gig ports, but I can only use 1 of them on each sup. If I try to configure a 2nd gig port on one of the Sups, it gives me an error saying that the port is only active if the switch only has 1 supervisor. Looks like you may be hitting a similar situation.

agugger Fri, 07/17/2009 - 14:40
User Badges:

Hello Kumar


You have to understand the internal organization of the 4500 Series.

With classis chassis 4506 & 4507 and classic modules

You have 32 internal 1 gigabit channels

Two of 32 are used by the supervisor for the 1 Gig uplinks

If you have two supervisors you have still only 2 internal channels but 4 interfaces on the front.

The remaining 30 internal channels are in groups of 6 for the 5 slots used.

Result in 6 gig in and 6 gig out per slot, don't care about type of line card with 6, 24 or 48 interfaces.


The Sup 5-10GE can serve up to 48 internal 1 gigabit channels and 2x 10 gig channels for the uplinks for the 4510 chassis.

But the rules are the same.

The two 2x 10 gig channels are used for the uplinks

If you have 2 supervisors with 4 10GE interfaces you can sill only use two.


Here is an additional trick.

The four 1 gig interfaces on the 5-10GE borrow 4 channels from the slot 10.

Per configuration can you select either to use the 4x 1 gig interfaces on the supervisor or the full performance of all 6x 1 gigabit channels on slot 10.

But again if have two supervisors 5-10GE wit total 8x 1 gig interfaces on the front you can only 4 of them use.

Even you can't use in 4507 Chassis the slots 8-10, the performance reserved for this slot is lost.


Similar case with the sup5 without 10GE.

They can serve up to 48 internal 1 gigabit channels including all up links.

If you use 2 supervisor of this type you borrow 4 channels from the slot 10.

Only in this case you can use all 4 uplinks on both supervisors.

So the remain two channels at slot 10 can only serve a 4302 line card with tow 1 gig uplink.


So in my point of view the supervisor looks like a memory multiplexer.

Or like Cisco says the channels do simultaneous shared memory access.


hth

andy


hclisschennai Sat, 07/18/2009 - 10:52
User Badges:

Hi Andy,


Awesome post. Very interesting. This helps us to understand the blocking architecture of these models.


Can you please share the link from where we can these subtle details, so that we will be able to plan the design, to avoid these kind of last moment surprise during implementation


RK

agugger Tue, 07/21/2009 - 23:43
User Badges:

Hi


My summary is the experience of 10 year working from Catalyst 4000 up to the current 4500E series. Unlucky wise Cisco never writes an architecture white paper like for 6500 Series exist. So there is no link to present how document the facts in simple way.


Andy


Actions

This Discussion