Wic card

Unanswered Question
Aug 4th, 2009

I have C3745-IPVOICE-M, Version 12.3(4) T4. I had a tech @ the remote installed a T1 card , how ever the card does not show on the config.

I did the command

Config t

#card type ?

E3

T3

# Controller?

T3 T3 controller

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
cisco steps Tue, 08/04/2009 - 09:23

Slot 0:

C3745 Mother board 2FE(TX)-3W Port adapter, 8 ports

Port adapter is analyzed

Port adapter insertion time 28w6d ago

EEPROM contents at hardware discovery:

PCB Serial Number : JAE075105AM

Processor type : 69

Top Assy. Part Number : 800-15934-03

Board Revision : B0

Fab Part Number : 28-4672-04

Deviation Number : 65535-65535

Manufacturing Test Data : FF FF FF FF FF FF FF FF

RMA Number : 0-0-0-0

RMA History : 00

RMA Test History : 00

Field Diagnostics Data : FF FF FF FF FF FF FF FF

Hardware Revision : 2.0

Fab Version : 04

Chassis Serial Number : JMX0804L006

Product (FRU) Number : C3745-2FE

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 4A 41 45 30 37 35 31 30 35 41 4D 09

0x10: 69 40 02 F7 C0 46 03 20 00 3E 3E 03 42 42 30 85

0x20: 1C 12 40 04 80 FF FF FF FF C4 08 FF FF FF FF FF

0x30: FF FF FF 81 00 00 00 00 04 00 03 00 C5 08 FF FF

0x40: FF FF FF FF FF FF 41 02 00 02 04 C2 8B 4A 4D 58

0x50: 30 38 30 34 4C 30 30 36 FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 0:

FT1 PMC4351

Hardware Revision : 1.2

PCB Serial Number : FOC10522498

Part Number : 73-8346-05

Board Revision : A0

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Deviation Number : 0-0

Product (FRU) Number : WIC-1DSU-T1-V2

Top Assy. Part Number : 800-22193-03

CLEI Code : IPUIAPRRAA

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 52 41 01 02 C1 8B 46 4F 43 31 30 35

0x10: 32 32 34 39 38 82 49 20 9A 05 42 41 30 03 00 81

0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 57 49 43

Leo Laohoo Tue, 08/04/2009 - 14:18

There are no controller or controller-related commands, such as channel-group, to configure. With this WIC card, service-module commands are used. The syntax with regard to the framing, line-code, and so on remains the same. In this scenario a full T1 card with 24 timeslots is used.

Please check out the Sample Configuration for this WIC.

http://www.cisco.com/en/US/products/hw/modules/ps3129/products_tech_note09186a0080093d70.shtml#sample_config

or

http://www.cisco.com/en/US/products/hw/modules/ps3129/products_tech_note09186a00800b1501.shtml#sample_cfg

Hope this helps.

Actions

This Discussion