cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
658
Views
0
Helpful
4
Replies

Wic card

cisco steps
Level 1
Level 1

I have C3745-IPVOICE-M, Version 12.3(4) T4. I had a tech @ the remote installed a T1 card , how ever the card does not show on the config.

I did the command

Config t

#card type ?

E3

T3

# Controller?

T3 T3 controller

4 Replies 4

paolo bevilacqua
Hall of Fame
Hall of Fame

Which exact card is that ? Check "show diag".

Slot 0:

C3745 Mother board 2FE(TX)-3W Port adapter, 8 ports

Port adapter is analyzed

Port adapter insertion time 28w6d ago

EEPROM contents at hardware discovery:

PCB Serial Number : JAE075105AM

Processor type : 69

Top Assy. Part Number : 800-15934-03

Board Revision : B0

Fab Part Number : 28-4672-04

Deviation Number : 65535-65535

Manufacturing Test Data : FF FF FF FF FF FF FF FF

RMA Number : 0-0-0-0

RMA History : 00

RMA Test History : 00

Field Diagnostics Data : FF FF FF FF FF FF FF FF

Hardware Revision : 2.0

Fab Version : 04

Chassis Serial Number : JMX0804L006

Product (FRU) Number : C3745-2FE

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 4A 41 45 30 37 35 31 30 35 41 4D 09

0x10: 69 40 02 F7 C0 46 03 20 00 3E 3E 03 42 42 30 85

0x20: 1C 12 40 04 80 FF FF FF FF C4 08 FF FF FF FF FF

0x30: FF FF FF 81 00 00 00 00 04 00 03 00 C5 08 FF FF

0x40: FF FF FF FF FF FF 41 02 00 02 04 C2 8B 4A 4D 58

0x50: 30 38 30 34 4C 30 30 36 FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 0:

FT1 PMC4351

Hardware Revision : 1.2

PCB Serial Number : FOC10522498

Part Number : 73-8346-05

Board Revision : A0

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Deviation Number : 0-0

Product (FRU) Number : WIC-1DSU-T1-V2

Top Assy. Part Number : 800-22193-03

CLEI Code : IPUIAPRRAA

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 52 41 01 02 C1 8B 46 4F 43 31 30 35

0x10: 32 32 34 39 38 82 49 20 9A 05 42 41 30 03 00 81

0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 57 49 43

That is not normal and you should engage the TAC on this.

Leo Laohoo
Hall of Fame
Hall of Fame

There are no controller or controller-related commands, such as channel-group, to configure. With this WIC card, service-module commands are used. The syntax with regard to the framing, line-code, and so on remains the same. In this scenario a full T1 card with 24 timeslots is used.

Please check out the Sample Configuration for this WIC.

http://www.cisco.com/en/US/products/hw/modules/ps3129/products_tech_note09186a0080093d70.shtml#sample_config

or

http://www.cisco.com/en/US/products/hw/modules/ps3129/products_tech_note09186a00800b1501.shtml#sample_cfg

Hope this helps.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card