Help needed: SRW224G4P password recovery

Unanswered Question

Hi,


I need help with password recovery on SRW224G4P. I couldn't get into the MENU by press ESC to interrupt the normal boot process. I tried many many times, no luck at all.


Below is what I see during boot up process:


Loading Diagnostic Image File : SRW224G4P_SRW248G4P_boot.bix

Diagnostic 1.0.1

User Mode

--- Performing Power-On Self Tests (POST) ---
DUMMY Test 1 ................. PASS
UART Loopback Test ........... PASS
POE UART Loopback Test ....... PASS
DRAM Test .................... PASS
Timer Test ................... PASS
Done All Pass.
------------------ DONE ---------------------


Loading Runtime Image File : SRW224G4P_SRW248G4P_image.bix
Runtime 1.0.2


Pass
root init done


Set Transition mode ...
[get stackingMac done ret_val] = 1
Assigned Unit ID:[1]
stacking DB: unit = 0, module type = 0

Finish Set Transition mode ...
Enter Transition mode ...
Finish Transition mode ...
Enter Master mode ...
Load certificate files : Starting
Load certificate files : Finished

Finish Master mode ...

Performing startup provision ...
CLI enter main (PROVISION)

................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
..............................................................
Notify provision complete

CLI provision has been completed


Provision Complete ...
Finish Provision Complete ...
[get stackingMac done ret_val] = 1
XFER: End of config sync.

Please press <Enter> to start Menu session!




Please help, let me know where I should press ESC or any other key....

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 1 (1 ratings)
Loading.
chrcoope Mon, 08/31/2009 - 06:26
User Badges:
  • Bronze, 100 points or more

Use this procedure. I tested it in my lab with your model switch and it worked here.


Regards,

Christopher

c.alperin Thu, 06/24/2010 - 08:33
User Badges:

Ctrl+U should make it on the boot process, and then reset to default configuration

Ganesh Hariharan Mon, 06/28/2010 - 06:31
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Member's Choice, February 2016

Hi,


I need help with password recovery on SRW224G4P. I couldn't get into the MENU by press ESC to interrupt the normal boot process. I tried many many times, no luck at all.


Below is what I see during boot up process:


Loading Diagnostic Image File : SRW224G4P_SRW248G4P_boot.bix

Diagnostic 1.0.1

User Mode

--- Performing Power-On Self Tests (POST) ---
DUMMY Test 1 ................. PASS
UART Loopback Test ........... PASS
POE UART Loopback Test ....... PASS
DRAM Test .................... PASS
Timer Test ................... PASS
Done All Pass.
------------------ DONE ---------------------


Loading Runtime Image File : SRW224G4P_SRW248G4P_image.bix
Runtime 1.0.2


Pass
root init done


Set Transition mode ...
[get stackingMac done ret_val] = 1
Assigned Unit ID:[1]
stacking DB: unit = 0, module type = 0

Finish Set Transition mode ...
Enter Transition mode ...
Finish Transition mode ...
Enter Master mode ...
Load certificate files : Starting
Load certificate files : Finished

Finish Master mode ...

Hi,


In order for you to reset the SRW224G4P you need to use a Data cable and use the console port of the switch. Once you are on the Console screen you could do a hardware reset.


Check out the below link for more information


http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=16615&p_created=1212523507&p_sid=6PuaAz3k&p_accessibility=0&p_redirect=&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9OTA2LDkwNiZwX3Byb2RzPTAmcF9jYXRzPTE3MjEsMTcyMyZwX3B2PSZwX2N2PTIuMTcyMyZwX3NjZl82PTEmcF9wYWdlPTEmcF9zZWFyY2hfdGV4dD1yZWNvdmVyIHRoZSBwYXNzd29yZCBvZiBteSBzd2l0Y2ggU1JXMjI0RzRQ&p_li=&p_topview=1



Hope to Help !!


Ganesh.H


Remember to rate the helpful post

Actions

This Discussion

Related Content