CME 4.0

Thanks,

Andy

Can you check the phones are getting an address from the router and there isn't a rogue dhcp server around.

No rogue dhcp going on anywhere on the network. Any other thoughts?

Thanks,

Andy

Send show interface for the ports involved.

I hope this is what you mean...

Gatehouse-Top#show interfaces fa0/6

FastEthernet0/6 is up, line protocol is up (connected)

Hardware is Fast Ethernet, address is 0024.5186.2a88 (bia 0024.5186.2a88)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 100Mb/s, media type is 10/100BaseTX

input flow-control is off, output flow-control is unsupported

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 2000 bits/sec, 3 packets/sec

213963 packets input, 25166233 bytes, 0 no buffer

Received 8026 broadcasts (0 multicasts)

0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog, 2656 multicast, 0 pause input

0 input packets with dribble condition detected

787873 packets output, 106528429 bytes, 0 underruns

0 output errors, 0 collisions, 1 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier, 0 PAUSE output

0 output buffer failures, 0 output buffers swapped out

-------------------------------------------------------------

Gatehouse-Top#show interfaces fa0/14

FastEthernet0/14 is up, line protocol is up (connected)

Hardware is Fast Ethernet, address is 0024.5186.2a90 (bia 0024.5186.2a90)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 100Mb/s, media type is 10/100BaseTX

input flow-control is off, output flow-control is unsupported

ARP type: ARPA, ARP Timeout 04:00:00

Last input never, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 4000 bits/sec, 3 packets/sec

281337 packets input, 68577875 bytes, 0 no buffer

Received 1332 broadcasts (0 multicasts)

0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog, 8 multicast, 0 pause input

0 input packets with dribble condition detected

859669 packets output, 388339871 bytes, 0 underruns

0 output errors, 0 collisions, 1 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier, 0 PAUSE output

0 output buffer failures, 0 output buffers swapped out

Also, they are both 7931 models, not 7961. Sorry.

Allright go ahead and upgrade firmware. I haven't checked what the latest is.

Hi,

If you havent tried, please perform a factory reset.

that has helped in one of our phones doing similar things.

Regards