09-14-2009 08:29 AM - edited 03-06-2019 07:43 AM
I need create class-map in the Cisco Switch 2950, but I dont can create it. I upgrade the IOS. The Ios running in the Switch is the following:
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA13, RELEASE SOFTWARE (fc2)
BOOT path-list: flash:/c2950-i6q4l2-mz.121-22.EA13.bin
I read the paper :
Catalyst 2950 and Catalyst 2955 Switch Software Configuration Guide, 12.1(22)EA2
But the version 12.1(22)Ea2 is available ??
Thanks
09-14-2009 09:20 AM
Hi Ricardo,
You should be fine with your existing IOS version. Here is the configuration guide for this:
09-14-2009 09:49 AM
It depends on what model of 2950 it is , if its a standard code box or enterprise box . If standard box then QOS may have limited availibilty . To define QOS parameters you must have the EI code which is model dependent. All code is the same for these boxes but the code has enough intelligence to know what box it is being loaded on , if your 2950 is not an EI box then class maps may not be available. A show version will tell you if it's a EI or standard box.
09-14-2009 11:30 AM
That is my output show version:
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA13, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by cisco Systems, Inc.
Compiled Fri 27-Feb-09 22:20 by amvarma
Image text-base: 0x80010000, data-base: 0x80570000
ROM: Bootstrap program is C2950 boot loader
Switch uptime is 19 minutes
System returned to ROM by power-on
System image file is "flash:/c2950-i6q4l2-mz.121-22.EA13.bin"
cisco WS-C2950-24 (RC32300) processor (revision R0) with 20957K bytes of memory.
Processor board ID FOC1009
Last reset from system-reset
**Running Standard Image**
24 FastEthernet/IEEE 802.3 interface(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: ommited
Motherboard assembly number: ommited
Power supply part number: ommited
Motherboard serial number: ommited
Power supply serial number: ommited
Model revision number: R0
Motherboard revision number: A0
Model number: WS-C2950-24
System serial number: ommited
Configuration register is 0xF
09-14-2009 11:35 AM
The output of the show : **Running Standard Image**
I can upgrade IOS to Enhanced Image or the hardware do not support the Enhanced Image?
Thanks
09-14-2009 11:45 AM
Check the Image requirements on the download page.
You may have or have not access to advanced / enhanced images as it depends on your support contracts.
09-14-2009 01:17 PM
I upgrade the IOS with this file : c2950-i6k2l2q4-mz.121-22.EA13.bin
And the Standard Image is enabled in the Switch ... :(
cisco WS-C2950-24 (RC32300) processor (revision R0) with 19912K bytes of memory.
Processor board ID FOC1009Z3QK
Last reset from system-reset
Running Standard Image
09-14-2009 01:14 PM
.
09-14-2009 02:11 PM
As I said before it is platform dependent and yours is running standard version so it cannot be upgraded.
09-14-2009 02:33 PM
The basic 2950-24 is an Standard Image (SI) only switch. Some of the Gig uplink ports, such as the 2950G, supports Enhanced Image (EI).
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: