09-16-2009 08:04 AM
Hi,
I've CUCM 7.02 with H323 GW for one cisco 2811 with 2 FXO ports, and i cannot do a outgoing call.
The call is placed and after 12 seconds the call disconect with " Cause Value=47, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=47)"
Regards,
Pedro Silva
09-16-2009 11:15 AM
Take "debug vpm signal" with "term mon". Also send voice-port configuration.
09-25-2009 06:54 AM
09-25-2009 07:05 AM
Under voice port configure
no battery-reversal
09-25-2009 07:16 AM
With the command "no battery-reversa" have the same problem.
incomig evertihng ok but outgoing after 12 seconds the call is off (but i don't have any audio in outgoing call)
sh voice call status
CallID CID ccVdb Port DSP/Ch Called # Codec Dial-peers
0x347 5AB 0x479D23F0 0/1/1 0/1:1 *0924915542 None 1/924915542
09-25-2009 07:22 AM
Configure:
no soft-offhook
and take debug vpm again. No need to use attachments.
09-25-2009 07:27 AM
voice-port 0/1/1
no battery-reversal
cptone PT
connection plar opx 8001801
impedance complex2
caller-id enable
!
VPM SIGNAL:
Sep 25 15:26:18.792: htsp_timer_stop3 htsp_setup_req
Sep 25 15:26:18.796: htsp_process_event: [0/1/1, FXOLS_ONHOOK, E_HTSP_SETUP_REQ]fxols_onhook_setup
Sep 25 15:26:18.796: [0/1/1] set signal state = 0xC timestamp = 0
Sep 25 15:26:18.796: htsp_timer - 1300 msec
Sep 25 15:26:20.096: htsp_process_event: [0/1/1, FXOLS_WAIT_DIAL_TONE, E_HTSP_EVENT_TIMER]fxols_wait_dial_timer htsp_dial
Sep 25 15:26:21.948: htsp_process_event: [0/1/1, FXOLS_WAIT_DIAL_DONE, E_DSP_DIALING_DONE]fxols_wait_dial_done htsp_alert
Sep 25 15:26:21.948: htsp_timer - 350 msec
Sep 25 15:26:21.948: htsp_call_bridged invoked
Sep 25 15:26:22.300: htsp_process_event: [0/1/1, FXOLS_WAIT_CUT_THRU, E_HTSP_EVENT_TIMER]fxols_handle_cut_thru
Sep 25 15:26:22.300: htsp_timer_stop
Sep 25 15:26:28.773: htsp_process_event: [0/1/1, FXOLS_OFFHOOK, E_DSP_SIG_0110]
Sep 25 15:26:28.773: htsp_timer_stop2
Sep 25 15:26:34.041: htsp_timer_stop3
Sep 25 15:26:34.041: htsp_process_event: [0/1/1, FXOLS_OFFHOOK, E_HTSP_RELEASE_REQ]fxols_offhook_release
Sep 25 15:26:34.041: htsp_timer_stop
Sep 25 15:26:34.041: htsp_timer_stop2
Sep 25 15:26:34.041: htsp_timer_stop3
Sep 25 15:26:34.041: [0/1/1] set signal state = 0x4 timestamp = 0
Sep 25 15:26:34.041: htsp_timer - 2000 msec
Sep 25 15:26:34.317: htsp_process_event: [0/1/1, FXOLS_GUARD_OUT, E_DSP_SIG_0110]
Sep 25 15:26:36.041: htsp_process_event: [0/1/1, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
Sep 25 15:26:36.041: htsp_process_event: [0/1/1, FXOLS_ONHOOK, E_DSP_SIG_0100]
09-25-2009 08:07 AM
Can you dial using a nromal telephone ?
Can you try "destination-pattern 9", check you have dialtone a dial after that.
09-25-2009 08:09 AM
i will try monday. Tnks for your help
09-28-2009 01:41 AM
09-28-2009 01:51 AM
Check that there is no number manipulation for the ip phones.
Beside that I would not know what to suggest.
09-28-2009 01:55 AM
i don't have any digit manipulation.
Any idea??
09-28-2009 03:18 AM
Which exact IOS are you using ?
09-28-2009 05:33 AM
System image file is "flash:c2800nm-advipservicesk9-mz.124-15.T9.bin"
10-05-2009 03:43 AM
Hi,
My problem is solved, my costumer have put a ASA in tranparent mode between CM and the gateway. I remove the
inspect H323 and everthig is working fine.
Regards,
Pedro Silva
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: