09-17-2009 11:59 AM
Good day.
I have a 2821 with following hardware but i'm unable to begin the configuration of the VWIC for some reason. I thought it was IOS related but i'm using the same version of code else where.
Version:
c2800nm-spservicesk9-mz.124-25b.bin
Hardware config:
C2821 Motherboard with 2GE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:01:05 ago
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-26921-04
Board Revision : E0
Deviation Number : 0
Fab Version : 03
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20090709
MAC Address block size : 32
CLEI Code : COMV410ARA
Product (FRU) Number : CISCO2821
Part Number : 73-8853-05
Version Identifier : V05
EEPROM format version 4
PVDM Slot 0:
48-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8540-05
Board Revision : C0
Deviation Number : 0
Fab Version : 04
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-48
Version Identifier : V01
EEPROM format version 4
WIC Slot 0:
VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1
Hardware Revision : 0.0
Top Assy. Part Number : 800-22628-05
Board Revision : C0
Deviation Number : 0
Fab Version : 04
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VWIC2-1MFT-T1/E1
Version Identifier : V01
EEPROM format version 4
I've tried all of the following but nothing seems to work.
WIN-DC-VG01(config)#network-clock-participate ?
aim AIM Module
slot Network Module Slot
wic WIC Module
WIN-DC-VG01(config)#network-clock-participate slo
WIN-DC-VG01(config)#network-clock-participate slot ?
<1-2> Slot Number
WIN-DC-VG01(config)#network-clock-participate slot 1
Slot is empty or does not support clock participate
WIN-DC-VG01(config)#network-clock-participate slot 2
Slot is empty or does not support clock participate
WIN-DC-VG01(config)#network-clock-participate wi
WIN-DC-VG01(config)#network-clock-participate wic ?
<0-3> Slot Number (physical)
WIN-DC-VG01(config)#network-clock-participate wic 0
WIC slot is empty or does not support clock participate
WIN-DC-VG01(config)#network-clock-participate wic 1
WIC slot is empty or does not support clock participate
WIN-DC-VG01(config)#network-clock-participate wic 2
WIC slot is empty or does not support clock participate
WIN-DC-VG01(config)#network-clock-participate wic 3
WIC slot is empty or does not support clock participate
I see that i only have slot 1 and 2 available and the 'sh diag' references slot 0...not sure why.
Any help would be appreciated.
Thanks.
Solved! Go to Solution.
09-17-2009 04:28 PM
It looks like you need to enter the "card type" command to specify whether this is a T1 or E1 card.
-nick
09-22-2009 02:34 AM
I think the config help only shows arbitary values anyway
09-17-2009 04:28 PM
It looks like you need to enter the "card type" command to specify whether this is a T1 or E1 card.
-nick
09-18-2009 06:46 AM
Worked perfectly thank you very much!
09-22-2009 02:34 AM
I think the config help only shows arbitary values anyway
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: