cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2672
Views
0
Helpful
13
Replies

Receive call

angeolivier
Level 1
Level 1

hello all,

i am new to use UC520 after make my config i can make call outside my office but i can't receive call. when i see to the console interface when call of outside come the BRI interface come UP but the IP phone who are associate to this number by DID don't ring. any help please.

13 Replies 13

Saurabh Verma
Level 4
Level 4

Can you send us the configuration and capture the ISDN debugs?

-Saurabh

To capture isdn debugs, go to "Troubleshoot > Voice Diagnostics > Voice Debug Log..." and check the box for ISDN, click on "Apply Debug" and follow the instructions for capturing the debugs.

Thanks,

Saurabh

Hello

This is UC520 configuration and ISDN debug captures.

Thanks

Steven Smith
Level 7
Level 7

Can you let me know what number was called and what number placed the call?

Can you also verify that you placed an inbound and an outbound call during the time of the traces?

During the trace, I have made first an outgoing call (from xxxxxxxx to xxxxxxxx), and then the incoming call (from xxxxxxx to xxxxxxxx).

Normally xxxxxx is transleted to the ip phone 340.

angeolivier
Level 1
Level 1

hello all,

I see again there are a mistake on ACD i don't no if is can play on my config to receive call ?

Until I'm reading the debugs incorrectly, I don't see any incoming calls. The debugs show only the outgoing call. I don't think the provider is sending the call in. Can you capture another debug, this time only for incoming call?

Thanks,
Saurabh

helo all

when i make call to a phone number xxxxxxxx  I see in same time in console interface   #sh isdn history UC 500 see only a  xxxx. i my config i say

01xxxxxx ----> 293, when i change 01xxxxx to xxx is ok how i can solve this.

Now, when I call someone, he sees xxx and not xxx.

Why???

thanks.

Saurabh Verma
Level 4
Level 4

Can you share the updated config?

-Saurabh

angeolivier
Level 1
Level 1

In attached file

Thanks

Saurabh Verma
Level 4
Level 4

In the config below, you have changed your caller-id as well

voice translation-rule 1111
  rule 1 /293/ /9540/
  rule 15 /.*/ /298/
!

Make the following changes:

voice translation-rule 1111
  rule 1 /293/ /0155389540/
  rule 15 /.*/ /298/
!

Thanks,

Saurabh

angeolivier
Level 1
Level 1

When, I change the configuration :

voice translation-rule 9
rule 1 /xxxxx/ /293/
!
voice translation-rule 1111
rule 1 /293/ /xxxxxx/
rule 15 /.*/ /298/
!
voice translation-rule 1112
rule 1 /^0/ //

I can receive call but I can't call outside.

And if I change too the number in :

voice translation-rule 9
rule 1 /xxxxxxxx/ /293/
!
voice translation-rule 1111
rule 1 /293/ /xxxxxx/
rule 15 /.*/ /298/
!
voice translation-rule 1112
rule 1 /^0/ //

I can't call outside and can't receive call. It's my initial problem.

I think, it's not a translation problem but a number format problem.

Thanks

Saurabh Verma
Level 4
Level 4

Alright, let's fix one thing at a time. Can you get calls working in both directions with the configuratoin below? I understand that with this, the person who receives the call gets your caller-id as 9540.

voice translation-rule 9
rule 1 /9540/ /293/
!
voice translation-rule 1111
rule 1 /293/ /9540/
rule 15 /.*/ /298/
!

If the above works, let's find from your ISDN provider the ISDN PLAN/TYPE that he is expecting for outgoing calls.

Thanks,

Saurabh

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: