2650XM dial-peer using Trunks

Answered Question
Sep 26th, 2009

Hi,

I got a customer with a 2650XM IOS vers. 12.4(19b) (c2600-adventerprisek9_ivs-mz.124-19b), I cannot use ports only Trunks and I cannot get the dial-peers to work. I programmed the Controller with the PRI and D-channel with a Trunk label but not voice-port is created.

I had to replace his router with a temporary 2821 and everything is Ok but of course I need to recover the 2821, his router was working before with another solution, not Cisco, so they didn't want to buy a new one and a PRI card.

I am guessing I don't understand the whole TRUNK programming for Dial-Peers, any help will be appreciated, below are the pieces of config and debug relevant to this.

Regards,

Hiram

**********

CONFIG

trunk group PSTN

description PRI Line to PSTN

!

controller T1 1/0

framing esf

linecode b8zs

pri-group timeslots 1-24

description PRI T1 for PSTN

!

interface Serial1/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-dms100

isdn incoming-voice voice

isdn supp-service name calling

trunk-group PSTN

no cdp enable

!

dial-peer voice 1 pots

incoming called-number .

trunk-group-label source PSTN

direct-inward-dial

!

dial-peer voice 201 pots

description Primary Outbound Dial Peer for 10 Digits - Local Services

preference 1

destination-pattern 8305[2-9]......

trunk-group-label target PSTN

prefix 305

!

dial-peer voice 1000 voip

preference 1

destination-pattern 1...

voice-class codec 5

voice-class h323 5

session target ipv4:192.168.204.21

incoming called-number 8T

dtmf-relay h245-alphanumeric

!

dial-peer voice 1011 voip

preference 1

destination-pattern 1...

voice-class codec 5

voice-class h323 5

session target ipv4:192.168.204.21

dtmf-relay h245-alphanumeric

!

**********

DEBUG

HQ1VGW1#

*Mar 2 07:57:46.828: //-1/80D9DD911300/DPM/dpAssociateIncomingPeerCore:

Calling Number=1000, Called Number=83059998002, Voice-Interface=0x0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

*Mar 2 07:57:46.828: //-1/80D9DD911300/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1000

*Mar 2 07:57:46.832: //-1/80D9DD911300/DPM/dpAssociateIncomingPeerCore:

Calling Number=1000, Called Number=83059998002, Voice-Interface=0x0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

*Mar 2 07:57:46.832: //-1/80D9DD911300/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1000

*Mar 2 07:57:46.848: //-1/80D9DD911300/DPM/dpMatchPeersCore:

Calling Number=, Called Number=83059998002, Peer Info Type=DIALPEER_INFO_SPEECH

*Mar 2 07:57:46.848: //-1/80D9DD911300/DPM/dpMatchPeersCore:

Match Rule=DP_MATCH_DEST; Called Number=83059998002

*Mar 2 07:57:46.848: //-1/80D9DD911300/DPM/dpMatchPeersCore:

No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1)

*Mar 2 07:57:46.848: //-1/80D9DD911300/DPM/dpMatchPeersMoreArg:

Result=NO_MATCH(-1)

HQ1VGW1#

I have this problem too.
0 votes
Correct Answer by Paolo Bevilacqua about 7 years 2 months ago

Under DP, it's "trunkgroup".

Note, yout DP 1 doesn't need or use it.

Note if you have no voice-port, likely you're not using the right hardware or do not have enough dsp. Check "show diag" about that

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
Paolo Bevilacqua Sat, 09/26/2009 - 12:47

Under DP, it's "trunkgroup".

Note, yout DP 1 doesn't need or use it.

Note if you have no voice-port, likely you're not using the right hardware or do not have enough dsp. Check "show diag" about that

hlarriuz Sat, 09/26/2009 - 14:01

Thanks for responding.

HQ1VGW1#sh diag

Slot 0:

C2650XM 1FE Mainboard Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time 17:09:56 ago

EEPROM contents at hardware discovery:

Hardware Revision : 3.0

PCB Serial Number : FFFF

Part Number : 73-7755-04

RMA History : 00

RMA Number : 0-0-0-0

Board Revision : A0

Deviation Number : 0-0

Product (FRU) Number : C2650XM-1FE

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 6E 41 03 00 C1 0B FF FF FF 46 46 46

0x10: 46 FF FF FF FF 82 49 1E 4B 04 04 00 81 00 00 00

0x20: 00 42 41 30 80 00 00 00 00 FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 0:

FT1 BT8360

Hardware revision 1.3 Board revision E0

Serial number 25639147 Part number 800-03279-04

FRU Part Number WIC-1DSU-T1=

Test history 0x0 RMA number 00-00-00

Connector type Wan Module

EEPROM format version 2

EEPROM contents (hex):

0x20: 02 11 01 03 01 87 38 EB 50 0C CF 04 00 00 00 00

0x30: 70 00 00 00 02 08 27 01 FF FF FF FF FF FF FF FF

Slot 1:

CT1 (CSU) Port adapter, 1 port

Port adapter is analyzed

Port adapter insertion time 17:09:55 ago

EEPROM contents at hardware discovery:

Hardware revision 1.1 Board revision B0

Serial number 29805542 Part number 800-01228-05

FRU Part Number NM-1CT1-CSU=

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x00: 01 26 01 01 01 C6 CB E6 50 04 CC 05 00 00 00 00

0x10: 58 00 00 00 04 05 08 00 FF FF FF FF FF FF FF FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF

HQ1VGW1#

HQ1VGW1#sh isdn status

Global ISDN Switchtype = primary-dms100

ISDN Serial1/0:23 interface

dsl 0, interface ISDN Switchtype = primary-dms100

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 0 CCBs = 0

The Free Channel Mask: 0x807FFFFF

Number of L2 Discards = 0, L2 Session ID = 2

Total Allocated ISDN CCBs = 0

HQ1VGW1#

Regards,

Hiram

hlarriuz Sat, 09/26/2009 - 15:11

I made those changes (trunkgroup, DP1) and the dial peers are matching but still not working, please check "ccapi inout".

Thanks is advanced.

*********

New dial-peer

dial-peer voice 1 pots

incoming called-number .

direct-inward-dial

!

dial-peer voice 201 pots

trunkgroup PSTN

description Primary Outbound Dial Peer for 10 Digits - Local Services

preference 1

destination-pattern 8305[2-9]......

prefix 305

!

dial-peer voice 1000 voip

preference 1

destination-pattern 1...

voice-class codec 5

voice-class h323 5

session target ipv4:192.168.204.21

incoming called-number 8T

dtmf-relay h245-alphanumeric

!

dial-peer voice 1011 voip

preference 1

destination-pattern 1...

voice-class codec 5

voice-class h323 5

session target ipv4:192.168.204.21

dtmf-relay h245-alphanumeric

!

Attachment: 
hlarriuz Sat, 09/26/2009 - 16:44

Thanks Dear Bevilacqua,

The issue with the dial-peers using trunk was resolved, now that I passed that step, I have another issue in my next step, the connection to the PSTN(T1/PRI), I will open a different post for that.

Thanks again.

Paolo Bevilacqua Sun, 09/27/2009 - 07:19

You cannot use this router for voice, it has no voice card.

The NM-1CT1 is only for data and modem, not voice.

You need NM-HDV-xxx for voice.

Actions

This Discussion