cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1088
Views
5
Helpful
6
Replies

VG224 Issue with UCM7 & MGCP

sohaildxbfze
Level 1
Level 1

Hi all,

m into crazy issue with mgcp VG224 some ports not showing correct status, when i dial port it plays busy infact port is available.Even no output from debug vpm signal.This is happeinng on some ports on same VG.Resetting @ VG & UCM doesnt solve it,even reload of VG224.

VG224 IOS ver:slot0:vg224-i6s-mz.124-5b.bin

UCM ver:7.0.2.20000-5

MGCP statistics are follows

VOIR01VG22406#sh mgcp stat

UDP pkts rx 662, tx 668

Unrecognized rx pkts 0, MGCP message parsing errors 0

Duplicate MGCP ack tx 0, Invalid versions count 0

CreateConn rx 13, successful 13, failed 0

DeleteConn rx 17, successful 13, failed 4

ModifyConn rx 0, successful 0, failed 0

DeleteConn tx 0, successful 0, failed 0

NotifyRequest rx 80, successful 74, failed 6

AuditConnection rx 0, successful 0, failed 0

AuditEndpoint rx 60, successful 60, failed 0

RestartInProgress tx 65, successful 65, failed 0

Notify tx 422, successful 422, failed 0

ACK tx 160, NACK tx 15

ACK rx 487, NACK rx 0

IP address based Call Agents statistics:

IP address 10.103.1.12, Total msg rx 662,

successful 647, failed 15

System resource check is DISABLED. No available statistic

DS0 Resource Statistics

-----------------------

Utilization: 0.00 percent

Total channels: 19

Addressable channels: 19

Inuse channels: 0

Disabled channels: 0

Free channels: 19

Below is VG224 config::::

resource policy

!

voice-card 0

!

interface FastEthernet0/0

ip address x.x.x.x x.x.x.x

duplex auto

speed auto

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

ip route 0.0.0.0 0.0.0.0 x.x.x.1

!

control-plane

!

voice-port 2/0

idle-voltage low

!

voice-port 2/1

!

voice-port 2/2

!

voice-port 2/3

!

voice-port 2/4

!

voice-port 2/5

!

voice-port 2/6

!

voice-port 2/7

!

voice-port 2/8

!

voice-port 2/9

!

voice-port 2/10

!

voice-port 2/11

!

voice-port 2/12

!

voice-port 2/13

!

voice-port 2/14

!

voice-port 2/15

!

voice-port 2/16

!

voice-port 2/17

!

voice-port 2/18

!

voice-port 2/19

!

voice-port 2/20

!

voice-port 2/21

!

voice-port 2/22

!

voice-port 2/23

!

ccm-manager redundant-host x.x.x.13 x.x.x.11

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config server x.x.x.11

ccm-manager config

!

mgcp

mgcp call-agent x.x.x.12 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

no mgcp package-capability res-package

mgcp package-capability sst-package

no mgcp package-capability fxr-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp fax t38 inhibit

mgcp rtp payload-type g726r16 static

!

mgcp profile default

!

dial-peer voice 99920 pots

service mgcpapp

port 2/0

!

dial-peer voice 99921 pots

service mgcpapp

port 2/1

!

dial-peer voice 99922 pots

service mgcpapp

port 2/2

!

dial-peer voice 99923 pots

service mgcpapp

port 2/3

!

dial-peer voice 99925 pots

service mgcpapp

port 2/5

!

dial-peer voice 99927 pots

service mgcpapp

port 2/7

!

dial-peer voice 999210 pots

service mgcpapp

port 2/10

!

dial-peer voice 999215 pots

service mgcpapp

port 2/15

!

dial-peer voice 999223 pots

service mgcpapp

port 2/23

!

dial-peer voice 999218 pots

service mgcpapp

port 2/18

!

dial-peer voice 999219 pots

service mgcpapp

port 2/19

!

dial-peer voice 999222 pots

service mgcpapp

port 2/22

!

dial-peer voice 99926 pots

service mgcpapp

port 2/6

!

dial-peer voice 99924 pots

service mgcpapp

port 2/4

!

dial-peer voice 99929 pots

service mgcpapp

port 2/9

!

dial-peer voice 999216 pots

service mgcpapp

port 2/16

!

dial-peer voice 999211 pots

service mgcpapp

port 2/11

!

dial-peer voice 999212 pots

service mgcpapp

port 2/12

!

dial-peer voice 999213 pots

service mgcpapp

port 2/13

!

Any help is highly appreciated!!!!!!!

1 Accepted Solution

Accepted Solutions

Hi,

MGCP isn't the best solution with VG224

SCCP with VG224 is more recommended and stable beside the more features you'll benefit from it as suppplementary services for example

thanks

View solution in original post

6 Replies 6

Hi,

MGCP isn't the best solution with VG224

SCCP with VG224 is more recommended and stable beside the more features you'll benefit from it as suppplementary services for example

thanks

Are you sure you have all the correct dial peers? If you have 24 phones on this system, not all of them are registered.

-nick

It same seem stupid but have you rung the port with a phone in it? I`ve had it before where I got fastbusy until I plugged a phone in the port

ofcourse , i rang the phone,, infact faxes are connect3ed to all vg ports

You should listen to the advice by hythamhadad, switch away from MGCP and you shall be fine.

We had the exact same issue on several VG224. Turned out to be an IOS bug resolved in 12.4(24)T. Since upgrading to this release, we have not had this happen again. Prior to this IOS upgrade, only resolution was a to reload the VG224. A reset in Call Manager for a given port would resolve issue for a sort time some of the time.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: