Hi

the module is recognised. it is up when i see in the sh ip int bri.

other side is the fiber to copper media converter.

GLC-T copper SFP module is connected to the HWIC.

sh run

interface GigabitEthernet0/3/0

ip address XX.XX.XX.XX 255.255.255.252

no negotiation auto

end

sh int

GigabitEthernet0/3/0 is up, line protocol is up

Hardware is PM-3387, address is 0025.45d2.dc64 (bia 0025.45d2.dc64)

Internet address is XX.XX.XX.XX/30

MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 1000Mb/s, link type is force-up, media type is T

output flow-control is XON, input flow-control is XON

ARP type: ARPA, ARP Timeout 04:00:00

Last input 22:04:16, output 00:00:02, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog, 0 multicast, 0 pause input

0 input packets with dribble condition detected

9994 packets output, 1021726 bytes, 0 underruns

0 output errors, 0 collisions, 6 interface resets

0 unknown protocol drops

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier, 0 pause output

0 output buffer failures, 0 output buffers swapped out

sh ver | inc image

c2800nm-advipservicesk9-mz.124-22.T2.bin

Thanks

Hello Mohammed,

keepalive is set

but

>>Last input 22:04:16, output 00:00:02, output hang never

and the interface is up/up

This is strange.

IOS version is new.

I will try to look at GLC-T support

what if you shut and then no shut the interface.

Hope to help

Giuseppe

thanks for your reply...

i tred to do that it does not work. i did change the GLC-T SFP but no luck. and yes the HWIC 1GE-SFP does support GLC-T. i did verify this with the cisco document.

Hi

the /30 link is t the ISP. there is n access lists.

Also the cable is connected to the media converter. I do not see any link on the media converter. however if I connect any other device on the Meda converter, its working perfectly OK.

is there any special config required on the Media converter except the normal interface configuraton?? does HWIC-1GE-SFP with GLC-T work?

Media converter? Why don't you just get a fibre optic SFP instead of the GLC-T?

Maybe it's because with the GLC-T, it won't negotiate duplex and speed. If you move the copper connection to the media converter from the GLC-T to any one of the RJ-45 of your routers (including the config), will you be able to ping across the /30 subnet?

I'm having the same issue. What did you do to resolve?