Rob Huffman Tue, 10/27/2009 - 05:38
User Badges:
  • Super Red, 40000 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 IP Telephony, Unified Communications

Hi Carl,


Call Pickup should work, I just tried it out in our lab to verify :)


The default settings for the VG248 feature codes are as follows:



Hang up last call #1



Transfer #2



Conference #3



Drop Last Conference Party #4



Forward all to voice mail **0



Call forward all **1



Cancel call forward **2



Pickup **3



Group Pickup **4



Redial *#



Malicious Call Identification ***



SpeedDial Voicemail *0



SpeedDial 1 *1



SpeedDial 2 *2



SpeedDial 3 *3



SpeedDial 4 *4



SpeedDial 5 *5



SpeedDial 6 *6



SpeedDial 7 *7



SpeedDial 8 *8



SpeedDial 9 *9



http://www.cisco.com/en/US/docs/voice_ip_comm/vg248/1_3_1/english/configuration/guide/vg248swv.html#wp1028593



Cheers!

Rob

Rob Huffman Thu, 10/29/2009 - 05:50
User Badges:
  • Super Red, 40000 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 IP Telephony, Unified Communications

Hey Carl,


No worries my friend :) Sadly, Directed Call Park, which is supported with the VG248 was not added until the release of CCM 4.2(x). Call Park requires an IP Phone with display to identify the Park # so this won't work with the VG248;


System Requirements for Directed Call Park

To operate, Directed Call Park requires the following software component:


•Cisco Unified Communications Manager 6.0 or later


A user can park and retrieve a call by using directed call park from any phone that can perform a transfer including Cisco Unified IP Phones 7905, 7912, 7920, 7940, 7960, and 7970. Cisco VG248 Analog Phone Gateways also support directed call park.


The following SCCP and SIP phones support directed call park BLF:


•Cisco Unified IP Phones (7941, 7961, 7970, 7971)


The following SCCP phones support directed call park BLF:


•Cisco Unified IP Phones (7905, 7912, 7920, 7940, 7960)


•Cisco Unified IP Phone Expansion Module 7914




System Requirements for Call Park


To operate, call park requires the following software component:


•Cisco Unified Communications Manager 5.0 or later


The following SCCP and SIP phones support call park with the Park softkey in the Standard User and Standard Feature softkey templates:


•Cisco Unified IP Phones (7941, 7961, 7970, 7971)


The following SCCP phones support call park with the Park softkey in the Standard User and Standard Feature softkey templates:


•Cisco Unified IP Phones (7905, 7912, 7920, 7931, 7940, 7960)




--------------------------------------------------------------------------------


Note You can configure Call Park on any line (except line 1) or button by using the programmable line key feature.



--------------------------------------------------------------------------------


The following SCCP phones support call park with the Call Park button on the phone button template:


•Cisco Unified IP Phone 30 (30 SP+ and 30 VIP)


•Cisco Unified IP Phone 12 (12 S, 12 SP, 12 SP+)


•Cisco Unified IP Phone 7910




CCM 4.2.x New Features


New and Changed Information for Cisco CallManager Features CCM 4.2


The following sections describe new and changed information related to Cisco CallManager features:


Multilevel Precedence and Preemption Enhancements


Device Mobility


Cisco CallManager Attendant Console and Call Pickup Limitation


Call Pickup Notification


** Directed Call Park




Hope this helps!

Rob

clougher01 Thu, 10/29/2009 - 13:26
User Badges:

Thanks for that Rob. So no alternative or similar feature with 4.1?

Actions

This Discussion