4507 Switch - Inactive Interfaces

luissoler79 · ‎10-28-2009

I have a 4507 switch with the following:

IOS ver cat4500-entservicesk9-mz.122-52.SG

Sup- WS-X4516-10GE

There are interfaces on the sup card that have a status of "inactive". How can I activate these interfaces? The #hw-module uplink select all command is not there!

iyde · ‎10-28-2009

Hi.

Either the VLAN assigned to these interfaces are not created in the VLAN database. Or there might be something with the number of ports supported - could you post a show module and show interface status?

HTH, Ingolf

luissoler79 · ‎10-29-2009

Below are the requested outputs. Thanks for the help!

#sh module

Chassis Type : WS-C4507R-E

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE1242XV6E

3 6 Sup V-10GE 10GE (X2), 1000BaseX (SFP) WS-X4516-10GE JAE1239W7KQ

4 6 Sup V-10GE 10GE (X2), 1000BaseX (SFP) WS-X4516-10GE JAE1239W437

M MAC addresses Hw Fw Sw Status

--+--------------------------------+---+------------+----------------+---------

1 0023.5e6d.a5c0 to 0023.5e6d.a5ef 2.5 Ok

3 0023.33ca.d680 to 0023.33ca.d685 5.1 12.2(31r)SGA 12.2(52)SG Ok

4 0023.33ca.d686 to 0023.33ca.d68b 5.1 12.2(31r)SGA 12.2(52)SG Ok

Mod Redundancy role Operating mode Redundancy status

----+-------------------+-------------------+----------------------------------

3 Active Supervisor SSO Active

4 Standby Supervisor SSO Standby hot

#sh int status

Port Status Vlan Duplex Speed Type

Te3/1 connect 9 full 10G No X2

Te3/2 inactive 9 full 10G No X2

Gi3/3 connected 316 full 1000 1000BaseLH

Gi3/4 connected trunk full 1000 1000BaseLH

Gi3/5 inactive 9 full 1000 No Gbic

Gi3/6 inactive 9 full 1000 No Gbic

Te4/1 notconnect 1 full 10G No X2

Te4/2 inactive 1 full 10G No X2

Gi4/3 notconnect 1 full 1000 No Gbic

Gi4/4 connected trunk full 1000 1000BaseLH

Gi4/5 inactive 1 full 1000 No Gbic

Gi4/6 inactive 1 full 1000 No Gbic

glen.grant · ‎10-29-2009

Put gbics in the ports..

luissoler79 · ‎10-29-2009

Thanks for the suggestion, I had tried that already. Unfortunately it did not resolve the problem.

rriquier · ‎06-29-2010

Hello, due to the fact you are using a redundant supervisor, some interfaces are disabled

. This is a normal behavior.

You can find on datasheet which combinations are possible

(http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps9294/product_data_sheet0900aecd806df543_ps4324_Products_Data_Sheet.html)

Table 4. Supervisor Engine 6-E High-Availability and Uplink Options

Feature and Description	Supervisor Engine 6-E
Redundant Capable	• Yes • Cisco Catalyst 4507R or 4507R-E model • Cisco Catalyst 4510R or 4510R-E model
Active Supervisor-Engine Uplinks in Redundant Mode	• Two 10 Gigabit Ethernet (wire-speed) or • Four 10 Gigabit Ethernet (2:1 oversubscribed)* or • Four Gigabit Ethernet (Cisco Twin Gig Converter Module) or • Eight Gigabit Ethernet (Cisco Twin Gig Converter Module)* or • One 10 Gigabit Ethernet and Two Gigabit Ethernet each supervisor-engine*
Active Supervisor-Engine Uplinks (Nonredundant Mode)	• Two 10 Gigabit Ethernet or • One 10 Gigabit Ethernet and 2 Gigabit Ethernet (Cisco Twin Gig Converter Module) or • Four Gigabit Ethernet (Cisco Twin Gig Converter Module)
Uplink Optic Types	SFP (Gigabit Ethernet) with Cisco Twin Gig Converter Module or X2 optics (10 Gigabit Ethernet ports)
SSO/NSF and ISSU	Yes

Regards,