2851 NM-AIR-WLC6-K9 WLC showing Unknown

Unanswered Question

We installed a NM-AIR-WLC6-K9 into our 2851 and it is showing "Unknown".

Below is our IOS Version and the message.


Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(21a), RELEASE SOFTWARE (fc1)


ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)


System image file is "flash:c2800nm-advipservicesk9-mz.124-21a.bin"


Cisco 2851 (revision 53.51) with 247808K/14336K bytes of memory.

Processor board ID FTX0911C0T2

2 Gigabit Ethernet interfaces

1 Serial interface

2 Channelized T1/PRI ports

1 Virtual Private Network (VPN) Module

8 Voice FXS interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62592K bytes of ATA CompactFlash (Read/Write)


Configuration register is 0x2102



Slot 1:

Unknown (type 1283) Port adapter

Port adapter is disabled

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.0

Top Assy. Part Number : 800-27210-01

Board Revision : B0

Deviation Number : 0

Fab Version : 02

PCB Serial Number : FOC09400PKT

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Fab Part Number : 28-5683-02

Manufacturing Test Data : 00 00 00 00 00 00 00 00

Field Diagnostics Data : 00 00 00 00 00 00 00 00

Product (FRU) Number : NM-AIR-WLC6-K9

CLEI Code : COUCABMCAA

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 05 03 41 01 00 C0 46 03 20 00 6A 4A 01

0x10: 42 42 30 88 00 00 00 00 02 02 C1 8B 46 4F 43 30

0x20: 39 34 30 30 50 4B 54 03 00 81 00 00 00 00 04 00

0x30: 85 1C 16 33 02 C4 08 00 00 00 00 00 00 00 00 C5

0x40: 08 00 00 00 00 00 00 00 00 CB 8E 4E 4D 2D 41 49

0x50: 52 2D 57 4C 43 36 2D 4B 39 C6 8A 43 4F 55 43 41

0x60: 42 4D 43 41 41 89 56 30 31 00 FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
dancampb Thu, 11/05/2009 - 08:39
User Badges:
  • Cisco Employee,

The WLCM is supported under the T trains of IOS. You need to switch to one of the software trains that support this module.

Actions

This Discussion

 

 

Trending Topics: Other Wireless Mobility

client could not be authenticated
Network Analysis Module (NAM) Products
Cisco 6500 nam
reason 440 driver failure
Cisco password cracker
Cisco Wireless mode