Caller id not shown for outgoing calls in CME

Unanswered Question
Nov 10th, 2009

I have a CME in which 20 ip phones connected, my issue is that calles are not showing the Caller Id of the originating phone,It is only showing my pilot number for all the calls

Call flow

IP Phone---CME---Mobile Number

I am not getting the originating ephone number instead getting the pilot nummber.

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
carlnewton Tue, 11/10/2009 - 04:22

What do you mean you are seeing the "pilot number" ?

IF you telnet to the router, enable "debug ISDN q931" and terminal monitor and make an outgoing call, you will see the call detail.

Check the "Calling number" detail on the call in question. If this shows the number you want to be shown then it could be the E1 provider replacing the calling number digits on your behalf.

If it doesnt show the number you want, it could be being modified by a translation outgoing. Check your dial peer for any commands relating to translations and tie these up with the translations at the top of the config.

These can be a little confusing if your not used to them so if you post the patterns themselves we can help decode them for you.

ajinc Tue, 11/10/2009 - 11:25

Here is the output of isdn q931 debug:

Also attaching the config for your sugession.

Router#csim start 85148712

csim: called number = 85148712, loop count = 1 ping count = 0

Nov 10 19:12:53.667: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Calling Number=, Called Number=85148712, Peer Info Type=DIALPEER_INFO_SPEECH

Nov 10 19:12:53.667: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Match Rule=DP_MATCH_DEST; Called Number=85148712

Nov 10 19:12:53.667: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:

Dial String=85148712, Expanded String=85148712, Calling Number=

Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH

Nov 10 19:12:53.671: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:

Result=Success(0); Outgoing Dial-peer=5 Is Matched

Nov 10 19:12:53.671: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Result=Success(0) after DP_MATCH_DEST

Nov 10 19:12:53.671: //-1/xxxxxxxxxxxx/DPM/dpMatchPeers:

Result=SUCCESS(0)

List of Matched Outgoing Dial-peer(s):

1: Dial-peer Tag=5

Nov 10 19:12:53.675: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is

0x0 0x0, Called num 5148712

Nov 10 19:12:53.675: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x027B

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9838A

Exclusive, Channel 10

Called Party Number i = 0x80, '5148712'

Plan:Unknown, Type:Unknown

Nov 10 19:12:53.719: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x8

27B

Channel ID i = 0xA9838A

Exclusive, Channel 10

Nov 10 19:12:53.739: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x8

27B

Progress Ind i = 0x8288 - In-band info or appropriate now available

ccappmib: insertion error. duplicate name CSIM

Nov 10 19:12:55.819: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Calling Number=, Called Number=83176030, Peer Info Type=DIALPEER_INFO_SPEECH

Nov 10 19:12:55.819: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Match Rule=DP_MATCH_DEST; Called Number=83176030

Nov 10 19:12:55.819: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:

Dial String=83176030, Expanded String=83176030, Calling Number=

Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH

Nov 10 19:12:55.819: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:

Result=Success(0); Outgoing Dial-peer=5 Is Matched

Nov 10 19:12:55.819: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Result=Success(0) after DP_MATCH_DEST

Nov 10 19:12:55.819: //-1/xxxxxxxxxxxx/DPM/dpMatchPeers:

Result=SUCCESS(0)

List of Matched Outgoing Dial-peer(s):

1: Dial-peer Tag=5

Nov 10 19:12:55.819: %SYS-3-MGDTIMER: Running timer, init, timer = 456196B0. -Pr

ocess= "Virtual Exec", ipl= 0, pid= 92, -Traceback= 0x415507BC 0x42860FC8 0x426

33E04 0x4159CB20 0x415C0894 0x42857378 0x4285735C

Nov 10 19:12:55.827: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is

0x0 0x0, Called num 3176030

Nov 10 19:12:55.827: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x027C

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98389

Exclusive, Channel 9

Called Party Number i = 0x80, '3176030'

Plan:Unknown, Type:Unknown

Attachment: 

Actions

This Discussion