Can any on help create a xml file for the following sip vendors config

Answered Question

Can some one help with a xml file for the SIP setup on a UC 500?

The outgoing SIP URI : sipconnect.ipcomms.net

Username: testtest1

Password: testtest1

the incoming is SIP URI : sipconnect.ipcomms.net but has a different login and password

Username: testtest2

Password: testtest2

____________________________________________________________

This is the sample config they gave me...

\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\

Sample VoIP Entry - H323 - Outbound Service

Sample POTs Entry - Inbound Service
!
dial-peer voice 6781475 pots
description IPC
huntstop
destination-pattern 6784601475
no digit-strip
port 0:D
!
dial-peer voice 1234 voip
description IPC
huntstop
destination-pattern . or .T
progress_ind setup enable 3
session target ipv4:xxx.xxx.xxx.xxx
dtmf-relay rtp-nte h245-signal h245-alphanumeric
codec g729r8
tech-prefix yyyyyyy
!
xxx.xxx.xxx.xxx is the IP address of IPC's destination gateway. yyyyyyy is the
prefix assigned to your account.

Sample VoIP Entry - SIP - Outbound Service

!
dial-peer voice 1234 voip
description IPC
huntstop
destination-pattern yyyyyyy. or yyyyyyy.T
progress_ind setup enable 3
session protocol sipv2
session target ipv4:xxx.xxx.xxx.xxx
dtmf-relay rtp-nte h245-signal h245-alphanumeric
codec g729r8
!
xxx.xxx.xxx.xxx is the IP address of IPC's destination gateway.
yyyyyyy is the prefix assigned to your account

I have this problem too.
0 votes
Correct Answer by Maulik Shah about 7 years 2 weeks ago

Attached is the first pass - give it a shot and let me know. If you confirm this all works we can post this for everyone to use.

Info on how to upload a template is below:
https://www.myciscocommunity.com/docs/DOC-9168

Correct Answer by Maulik Shah about 7 years 3 weeks ago

May need some more info to generate this file (note assume you will do the testing) - here is the typical list - items in bold are where we need your input

Name of SP: IPCOMMS

Dial Plan Locale (Country)

Fields to show on the SIP Trunk tab:

Proxy Server (Primary) Y/N

Proxy Server (Backup) Y/N

Registrar Server Y/N

Outbound Proxy Server Y/N

Digest Authentication (username / password) Yes (per your note below)

Other:

Voice codec: G729r8 (per your note below)

Fax protocol  T.38 / G711ulaw upspeed / G711alaw upspeed

DTMF RFC 2833  with RTP payload type 101 (default) - can change to any vaue from 96 to 127

Register all DIDs Y/N

If register all DIDs, then - all DIDs have same password OR unique password

DSCP marking Signaling cs3

DSCP marking RTP ef

Also, did not follow the different usernames / passwords for inbound versus outbound - the UC500 does not authenticate inbound SIP requests using username / password but using the IP address of the SIP proxy at the provider

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (2 ratings)
Loading.
Correct Answer
Maulik Shah Fri, 11/20/2009 - 10:29

May need some more info to generate this file (note assume you will do the testing) - here is the typical list - items in bold are where we need your input

Name of SP: IPCOMMS

Dial Plan Locale (Country)

Fields to show on the SIP Trunk tab:

Proxy Server (Primary) Y/N

Proxy Server (Backup) Y/N

Registrar Server Y/N

Outbound Proxy Server Y/N

Digest Authentication (username / password) Yes (per your note below)

Other:

Voice codec: G729r8 (per your note below)

Fax protocol  T.38 / G711ulaw upspeed / G711alaw upspeed

DTMF RFC 2833  with RTP payload type 101 (default) - can change to any vaue from 96 to 127

Register all DIDs Y/N

If register all DIDs, then - all DIDs have same password OR unique password

DSCP marking Signaling cs3

DSCP marking RTP ef

Also, did not follow the different usernames / passwords for inbound versus outbound - the UC500 does not authenticate inbound SIP requests using username / password but using the IP address of the SIP proxy at the provider

Name of SP: IPCOMMS

Dial Plan Locale (Country) North America

Fields to show on the SIP Trunk tab:

Proxy Server (Primary) sipconnect.ipcomms.net

Proxy Server (Backup) N

Registrar Server sipconnect.ipcomms.net

Outbound Proxy Server sipconnect.ipcomms.net

Digest Authentication (username / password) Yes (per your note below)??  YES

Other:

Voice codec: G711ulaw (per your note below)

Fax protocol G711ulaw upspeed

DTMF RFC 2833  with RTP payload type 101

Register all DIDs Y

If register all DIDs, then - all DIDs have same password

DSCP marking Signaling cs3

DSCP marking RTP ef

Also, did not follow the different usernames / passwords for inbound versus outbound - the UC500 does not authenticate inbound SIP requests using username / password but using the IP address of the SIP proxy at the provider

Actions

This Discussion