11-23-2009 08:14 AM - edited 03-04-2019 06:47 AM
Hey all.
I am configuring a 7204 with two DS3 circuits that are being channelized into 28 T1s each. I want to make sure I have them configured correctly before I start turning up circuits.
I have done research but connot find anything for multiple DS3s and creating multiple channel groups on one router.
Correct me if I am wrong but can I just create two channel-groups, one for each card. I know T1s have 24 timeslots. Should this work?
Again I have little experience configuring these circuits. I am going by my research.
controller T3 1/0
framing m23
cablelength 450
t1 1 channel-group 0 timeslots 1-24
t1 2 channel-group 0 timeslots 1-24
t1 3 channel-group 0 timeslots 1-24
t1 4 channel-group 0 timeslots 1-24
t1 6 channel-group 0 timeslots 1-24
t1 7 channel-group 0 timeslots 1-24
t1 8 channel-group 0 timeslots 1-24
t1 9 channel-group 0 timeslots 1-24
t1 10 channel-group 0 timeslots 1-24
t1 11 channel-group 0 timeslots 1-24
t1 12 channel-group 0 timeslots 1-24
t1 13 channel-group 0 timeslots 1-24
t1 14 channel-group 0 timeslots 1-24
t1 15 channel-group 0 timeslots 1-24
t1 17 channel-group 0 timeslots 1-24
t1 18 channel-group 0 timeslots 1-24
t1 19 channel-group 0 timeslots 1-24
t1 20 channel-group 0 timeslots 1-24
t1 21 channel-group 0 timeslots 1-24
t1 22 channel-group 0 timeslots 1-24
t1 23 channel-group 0 timeslots 1-24
t1 24 channel-group 0 timeslots 1-24
t1 25 channel-group 0 timeslots 1-24
t1 26 channel-group 0 timeslots 1-24
t1 27 channel-group 0 timeslots 1-24
t1 28 channel-group 0 timeslots 1-24
controller T3 2/0
framing m23
cablelength 450
t1 1 channel-group 1 timeslots 1-24
t1 2 channel-group 1 timeslots 1-24
t1 3 channel-group 1 timeslots 1-24
t1 4 channel-group 1 timeslots 1-24
t1 6 channel-group 1 timeslots 1-24
t1 7 channel-group 1 timeslots 1-24
t1 8 channel-group 1 timeslots 1-24
t1 9 channel-group 1 timeslots 1-24
t1 10 channel-group 1 timeslots 1-24
t1 11 channel-group 1 timeslots 1-24
t1 12 channel-group 1 timeslots 1-24
t1 13 channel-group 1 timeslots 1-24
t1 14 channel-group 1 timeslots 1-24
t1 15 channel-group 1 timeslots 1-24
t1 17 channel-group 1 timeslots 1-24
t1 18 channel-group 1 timeslots 1-24
t1 19 channel-group 1 timeslots 1-24
t1 20 channel-group 1 timeslots 1-24
t1 21 channel-group 1 timeslots 1-24
t1 22 channel-group 1 timeslots 1-24
t1 23 channel-group 1 timeslots 1-24
t1 24 channel-group 1 timeslots 1-24
t1 25 channel-group 1 timeslots 1-24
t1 26 channel-group 1 timeslots 1-24
t1 27 channel-group 1 timeslots 1-24
t1 28 channel-group 1 timeslots 1-24
Thanks for your help!
Solved! Go to Solution.
11-23-2009 08:19 AM
Yes. You can reuse channel-group 0 for both, because the interface ID will discriminate anyway.
11-23-2009 08:19 AM
Yes. You can reuse channel-group 0 for both, because the interface ID will discriminate anyway.
11-23-2009 08:42 AM
Cool.
Thanks a bunch!
11-23-2009 09:12 AM
No problem. Thank you for the nice rating and good luck!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: