12-08-2009 09:42 AM - edited 03-04-2019 06:54 AM
I'm just not sure what part of the config I am doing wrong or there is some bug i am running into. I am running c3725-advipservicesk9-mz.124-15.T9.bin.
The following is the config i have on the router.
interface Tunnel10
description ISATAP itnterface for windows and linux
no ip address
no ip redirects
ipv6 address FD39:26B1:DA1C:2::/64 eui-64
ipv6 enable
no ipv6 nd ra suppress
ipv6 ospf 1 area 0
tunnel source FastEthernet0/0
tunnel mode ipv6ip isatap
This is the interface brief
ipv6gateway#sh ipv6 int brief
FastEthernet0/0 [up/up]
FastEthernet0/1 [up/up]
FE80::C000:2EFF:FEF1:1
FD39:26B1:DA1C:1::1
Tunnel0 [up/up]
FE80::C000:2EFF:FEF1:0
unnumbered (Tunnel10)
Tunnel10 [up/up]
FE80::C000:2EFF:FEF1:0
FD39:26B1:DA1C:2:C000:2EFF:FEF1:0
ipv6gateway#sh ipv6 route
IPv6 Routing Table - 5 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route, M - MIPv6
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
D - EIGRP, EX - EIGRP external
C FD39:26B1:DA1C:1::/64 [0/0]
via ::, FastEthernet0/1
L FD39:26B1:DA1C:1::1/128 [0/0]
via ::, FastEthernet0/1
C FD39:26B1:DA1C:2::/64 [0/0]
via ::, Tunnel10
L FD39:26B1:DA1C:2:C000:2EFF:FEF1:0/128 [0/0]
via ::, Tunnel10
L FF00::/8 [0/0]
via ::, Null0
In XP, I ran 'netsh int ipv6 isatap set router 10.156.68.40'.
Tunnel adapter Teredo Tunneling Pseudo-Interface:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : FF-FF-FF-FF-FF-FF-FF-FF
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : fe80::ffff:ffff:fffd%5
Default Gateway . . . . . . . . . :
NetBIOS over Tcpip. . . . . . . . : Disabled
Tunnel adapter Automatic Tunneling Pseudo-Interface:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Automatic Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 0A-9C-35-54
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : fe80::5efe:10.156.53.84%2
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
fec0:0:0:ffff::2%1
fec0:0:0:ffff::3%1
NetBIOS over Tcpip. . . . . . . . : Disabled
C:\Documents and Settings\ggee>netsh interface ipv6 show route
Querying active state...
No entries were found.
What part am I doing wrong? Is there a better IOS I should be using? What address should I use to ping6?
Thanks,
Greg
Solved! Go to Solution.
12-11-2009 08:01 PM
Hi,
I'm also using VB ;-)
Here is what I have when my router is off:
Tunnel adapter Automatic Tunneling Pseudo-Interface:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Automatic Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : AC-10-00-01
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : fe80::5efe:172.16.0.1%2
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%3
fec0:0:0:ffff::2%3
fec0:0:0:ffff::3%3
NetBIOS over Tcpip. . . . . . . . : Disabled
Once my router is ON:
C:\Documents and Settings\laaubert>netsh interface ipv6 isatap set router 172.16.0.254
Ok.
C:\Documents and Settings\laaubert>ipconfig /all
...
Tunnel adapter Automatic Tunneling Pseudo-Interface:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Automatic Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : AC-10-00-01
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 2011:1::5efe:172.16.0.1
IP Address. . . . . . . . . . . . : fe80::5efe:172.16.0.1%2
Default Gateway . . . . . . . . . : fe80::5efe:172.16.0.254%2
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%3
fec0:0:0:ffff::2%3
fec0:0:0:ffff::3%3
NetBIOS over Tcpip. . . . . . . . : Disabled
Here is my router configuration:
ipv6 unicast-routing
ipv6 cef
!
interface Tunnel0
description ISATAP
no ip address
no ip redirects
ipv6 address 2011:1::/64 eui-64
ipv6 enable
no ipv6 nd ra suppress
tunnel source Ethernet1/0
tunnel mode ipv6ip isatap
!
interface Ethernet1/0
description ISATAP GW
ip address 172.16.0.254 255.255.255.0
!
I used 12.2(33)SRE.
You can run debug ipv6 icmp and debug ipv6 packet to track the RA and RS:
*Dec 12 03:59:01.515: IPV6: source FE80::5EFE:AC10:1 (Tunnel0)
*Dec 12 03:59:01.515: dest FF02::2
*Dec 12 03:59:01.515: traffic class 0, flow 0x0, len 48+20, prot 58, hops 255, forward to ulp
*Dec 12 03:59:01.515: ICMPv6: Received R-Solicit, Src=FE80::5EFE:AC10:1, Dst=FF02::2
*Dec 12 03:59:01.524: IPV6: source FE80::5EFE:AC10:FE (local)
*Dec 12 03:59:01.524: dest FE80::5EFE:AC10:1 (Tunnel0)
*Dec 12 03:59:01.524: traffic class 224, flow 0x0, len 96+0, prot 58, hops 255, originating
*Dec 12 03:59:01.524: IPv6-Fwd: Sending on Tunnel0
*Dec 12 03:59:01.524: ICMPv6: Sent R-Advert, Src=FE80::5EFE:AC10:FE, Dst=FE80::5EFE:AC10:1
HTH
Laurent.
12-11-2009 07:05 AM
I guess I should ask, has anyone done ISATAP from Windows XP? How?
Thanks,
Greg
12-11-2009 08:37 AM
Hi Greg,
Can you ping 10.156.68.40 from your station ?
Your tunnel configuration looks good.
I did the same configuration on my laptop (XR SP2) and it's working fine.
HTH
Laurent.
12-11-2009 09:37 AM
Yes, I have no problem doing ping and telnet to the router. Out of curiosity,
what router model and IOS version are you using?
I am trying on:
Cisco 3725
c3725-advipservicesk9-mz.124-15.T9.bin
Now to be specific, My XP SP3 is running in Virtual box while I test this setup. Maybe SP3 has issues.
Thanks,
Greg
12-11-2009 11:40 AM
Related to above, how can I tell if it works? How do I test it?
Greg
12-11-2009 08:01 PM
Hi,
I'm also using VB ;-)
Here is what I have when my router is off:
Tunnel adapter Automatic Tunneling Pseudo-Interface:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Automatic Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : AC-10-00-01
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : fe80::5efe:172.16.0.1%2
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%3
fec0:0:0:ffff::2%3
fec0:0:0:ffff::3%3
NetBIOS over Tcpip. . . . . . . . : Disabled
Once my router is ON:
C:\Documents and Settings\laaubert>netsh interface ipv6 isatap set router 172.16.0.254
Ok.
C:\Documents and Settings\laaubert>ipconfig /all
...
Tunnel adapter Automatic Tunneling Pseudo-Interface:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Automatic Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : AC-10-00-01
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 2011:1::5efe:172.16.0.1
IP Address. . . . . . . . . . . . : fe80::5efe:172.16.0.1%2
Default Gateway . . . . . . . . . : fe80::5efe:172.16.0.254%2
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%3
fec0:0:0:ffff::2%3
fec0:0:0:ffff::3%3
NetBIOS over Tcpip. . . . . . . . : Disabled
Here is my router configuration:
ipv6 unicast-routing
ipv6 cef
!
interface Tunnel0
description ISATAP
no ip address
no ip redirects
ipv6 address 2011:1::/64 eui-64
ipv6 enable
no ipv6 nd ra suppress
tunnel source Ethernet1/0
tunnel mode ipv6ip isatap
!
interface Ethernet1/0
description ISATAP GW
ip address 172.16.0.254 255.255.255.0
!
I used 12.2(33)SRE.
You can run debug ipv6 icmp and debug ipv6 packet to track the RA and RS:
*Dec 12 03:59:01.515: IPV6: source FE80::5EFE:AC10:1 (Tunnel0)
*Dec 12 03:59:01.515: dest FF02::2
*Dec 12 03:59:01.515: traffic class 0, flow 0x0, len 48+20, prot 58, hops 255, forward to ulp
*Dec 12 03:59:01.515: ICMPv6: Received R-Solicit, Src=FE80::5EFE:AC10:1, Dst=FF02::2
*Dec 12 03:59:01.524: IPV6: source FE80::5EFE:AC10:FE (local)
*Dec 12 03:59:01.524: dest FE80::5EFE:AC10:1 (Tunnel0)
*Dec 12 03:59:01.524: traffic class 224, flow 0x0, len 96+0, prot 58, hops 255, originating
*Dec 12 03:59:01.524: IPv6-Fwd: Sending on Tunnel0
*Dec 12 03:59:01.524: ICMPv6: Sent R-Advert, Src=FE80::5EFE:AC10:FE, Dst=FE80::5EFE:AC10:1
HTH
Laurent.
12-18-2009 09:35 AM
Thanks. Moving from a 3725 running c3725-advipservicesk9-mz.124-15.T9.bin to a 7200 running c7200-adventerprisek9-mz.122-33.SRC.bin made it all work.
Thanks,
Greg
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: