Hello,

Our FWSM module went down today. After enable the power and reset the module, It is again working fine.

Here are some logs and diagnostic tests are attached:

Before Reset:

Dec 14  06:50:20.072 KSA: %SNMP-5-MODULETRAP: Module 6 [Down] Trap

Dec 14  06:50:20.068 KSA: SP: The PC in slot 6 is shutting down. Please wait  ...

Dec 14  06:50:35.080 KSA: SP: shutdown_pc_process:No response from module  6

Dec 14  06:50:36.088 KSA: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off  (Reset)

Dec 14  06:52:16.964 KSA: %DIAG-SP-6-RUN_MINIMUM: Module 6: Running Minimal  Diagnostics...

Dec 14  06:52:18.980 KSA: %SNMP-5-MODULETRAP: Module 6 [Up] Trap

Dec 14  06:52:18.980 KSA: %SVCLC-5-FWVTPMODE: VTP mode is set to  non-transparent

Dec 14  06:52:19.020 KSA: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been  disabled.

Dec 14  06:52:19.868 KSA: %DIAG-SP-6-DIAG_OK: Module 6: Passed Online  Diagnostics

Dec 14  06:52:33.048 KSA: %OIR-SP-6-INSCARD: Card inserted in slot 6, interfaces are now  online

Dec 14  06:54:18.564 KSA: %SNMP-5-MODULETRAP: Module 6 [Down] Trap

Dec 14  06:54:18.564 KSA: SP: The PC in slot 6 is shutting down. Please wait  ...

Dec 14  06:54:33.576 KSA: SP: shutdown_pc_process:No response from module  6

Dec 14  06:54:34.588 KSA: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off  (Reset)

Dec 14  07:03:23.984 KSA: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off  (Module  Failed SCP dnld)

SWITCH#sh  module power

6   Firewall Module                        on            off  (Module  Failed SCP  dnld)

SWITCH#sh  module

Mod  MAC          addresses                       Hw    Fw           Sw                  Status

6       XXXXXXXXX to XXXXXXXXXXX               3.0   7.2(1)       8.5(0.46)RFW   PwrDown

After Reset:

Dec 14  08:49:39.228 KSA: %DIAG-SP-6-RUN_MINIMUM: Module 6: Running Minimal  Diagnostics...

Dec 14  08:49:41.248 KSA: %SNMP-5-MODULETRAP: Module 6 [Up] Trap

Dec 14  08:49:41.248 KSA: %SVCLC-5-FWVTPMODE: VTP mode is set to  non-transparent

Dec 14  08:49:41.284 KSA: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been  disabled.

Dec 14  08:49:42.188 KSA: %DIAG-SP-6-DIAG_OK: Module 6: Passed Online  Diagnostics

Dec 14  08:49:53.932 KSA: %OIR-SP-6-INSCARD: Card inserted in slot 6, interfaces are  now online

SWITCH#sh  module

Mod  MAC          addresses                       Hw    Fw           Sw            Status

   6      XXXXXXXXXX to XXXXXXXXXXX             3.0   7.2(1)       3.1(4)           Ok

===================

I want to know the reason behind this module power down.

We have Cisco 6513 with IOS Version 12.2(18)SXF17

Regards,

Anser