cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1034
Views
0
Helpful
9
Replies

frame-relay issue

sourabh1000_2
Level 1
Level 1

hello friends,

i have configured 2 routers with simple frame-relay config as follows

diagram

R1   FR   R2

config

R1

interface Serial0/1
ip address 10.0.0.1 255.0.0.0
encapsulation frame-relay
serial restart-delay 0
end

R2

interface Serial0/2
ip address 10.0.0.2 255.0.0.0
encapsulation frame-relay
serial restart-delay 0
end

ISSUE-->

from R1, i am able to ping 10.0.0.2 but i am not able to ping self ip address (10.0.0.1) of router R1.

errors i am received are as follows::::

R1#pin 10.0.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:

*Mar  1 00:21:59.499: Serial0/1:Encaps failed--no map entry link 7(IP).
*Mar  1 00:22:01.495: Serial0/1:Encaps failed--no map entry link 7(IP).
*Mar  1 00:22:03.495: Serial0/1:Encaps failed--no map entry link 7(IP).
*Mar  1 00:22:05.495: Serial0/1:Encaps failed--no map entry link 7(IP).
*Mar  1 00:22:07.495: Serial0/1:Encaps failed--no map entry link 7(IP).
Success rate is 0 percent (0/5)

please suggest the reason!!

Thanks and Regards,

Sourabh D

1 Accepted Solution

Accepted Solutions

Marwan ALshawi
VIP Alumni
VIP Alumni

this is becuase the local interface is not associated with any FR DLCI

to get it workig

i will assume as you mentioned R1 and R2 they can ping each other

falso from your config,  you are counting on invers arp

find out the DLCI used by R1 to reach R2

show frame-relay map

lets say the dlci used is 100

int R1

int s0/1

frame-relay map ip 10.0.0.1 100 br

good luck

if helpful Rate

View solution in original post

9 Replies 9

Marwan ALshawi
VIP Alumni
VIP Alumni

this is becuase the local interface is not associated with any FR DLCI

to get it workig

i will assume as you mentioned R1 and R2 they can ping each other

falso from your config,  you are counting on invers arp

find out the DLCI used by R1 to reach R2

show frame-relay map

lets say the dlci used is 100

int R1

int s0/1

frame-relay map ip 10.0.0.1 100 br

good luck

if helpful Rate

hello,

thank you very much for prompt reply

issue is resolved

you welcome

by the i can see you did rated the post with issue solved but the rating is not apreating like 4 or 5

is it a bug here ???

anyway i am glad your issue solved

Hello Marwan,

your rating will be correct.

Dan has explained in Netpro ideas that now when an answer is flagged as solved automatically provides a 5 rate.

He also explained that the new system is slower so it is possible to see for some time an answer flagged as solved with no rating associated to it, but is should be a temporary effect.

Best Regards

Giuseppe

Giuseppe

Apologies, didn't see your post.

Happy xmas and hope you have great new year. And more importantly, not long to go for your super bronze star and about time too

Jon

Hi all,

I second Jon's comments about Giuseppe's star. It might be difficult for him to accomplish the new star before new year comes if we take into account the activity in the forums these days, so I might just post some routing/mpls questions to push things a little bit.

As for the issue in the rating of this thread, yes, Dan might say it was some 'hiccup'. I noticed another type of 'hiccup' earlier (at the time Giuseppe and Jon posted). Because there is not much activity across the sections these days, I use the bottom of this page: https://supportforums.cisco.com/people/ to see recent avtivity, and for some time it didn't display anything. Now everything is back to normal regarding this last issue.

Best wishes,

Maria

Hello Jon, Maria,

Jon: you couldn't see my post we have published it at the same time 4.02!

I wish you an year of peace and full of good things in life. For Christmas is a little late.

Maria: no problems for the "first dan" star it can arrive next year.

Best Regards

Giuseppe

Marwan

The new site is slightly different. If a question is marked as answered you automatically get 5 points.

Jon

Thank you guys for your replay

but i think i havn't got any point yet !!

let me check it tomorrow and see

i am only concerned that, if there is something need to be fixed in the site

anyway wish you a happy new year guys

Marwan

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: