Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
4049
Views
0
Helpful
3
Replies

Logs on router

sameer.mulgund
Level 1
Level 1

‎01-04-2010 10:19 PM - edited ‎03-04-2019 07:07 AM

hi All,

We have observed below logs on one of our customers.

dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed
dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed

What are these logs for and what do they indicate? Lately we have been observing such logs more routers but unable to come up with concrete resolution.

The router in discussion is a Cisco 3845 router with IOS - c3845-spservicesk9-mz.124-12c.bin.

Regards

Sameer

Labels:
0 Helpful
3 Replies 3

LordFlasheart
Level 1
Level 1

‎01-05-2010 01:30 AM

I found the following for Tx errors. Not sure if you can gain anything from it though......

CSCsu45780

Symptoms: The following error message is displayed if the DSU bandwidth is configured with a value other than the default of 44210 for T3 on an NM-1T3/E3 module:

dsxpnm_gt96k_abort_tx_mpsc:Aborting Tx mpsc failed

Conditions: The symptom is observed when the DSU bandwidth is changed to a value other than the default of 44210. It mostly occurs with values below 1000.

Workaround: Leave the DSU bandwidth at the default of 44210.

Is it happening on a NM-1T3/E3 module?

0 Helpful

sameer.mulgund
Level 1
Level 1
In response to LordFlasheart

‎01-05-2010 01:41 AM

thanks. yes we have observe this issue for NM-1T3/E3 module.

If we are leaving DSU bandwidth as T3 speed then how to configure the channelized links less than T3 or E3? Say 20Mb or 15Mb.

Regards

Sameer

0 Helpful

paolo bevilacqua
Hall of Fame
Hall of Fame
In response to sameer.mulgund

‎01-05-2010 04:07 AM

You could try traffic shaping. Or insist with Cisco for a solution.

0 Helpful
Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card