01-13-2010 06:01 AM - edited 03-06-2019 09:16 AM
Hi I have a problem installing WS-SVC-CMM module in 6509-E. The problem is that the module goes down and stays in that state.
Regards
Goce
01-13-2010 06:36 AM
What IOS are you running on the switch ?
Jon
01-14-2010 07:29 AM
Hi Jon,
This is the IOS on the 6500 : s72033-advipservicesk9-mz.122-33.SXI2a.bin
Regards,
Goce
01-14-2010 07:50 AM
hotshot979 wrote:
Hi Jon,
This is the IOS on the 6500 : s72033-advipservicesk9-mz.122-33.SXI2a.bin
Regards,
Goce
Sorry, should have asked, what supervisor are you running ?
Also, can you post output of
sh module
sh power or sh env power
Jon
01-14-2010 08:36 AM
Hi Goce,
Is this a new installation or an older one?
Are you using this module with Sup720-10G in VSS configuration. If yes, then it is not supported in VSS configuration.
If it is not the VSS configuration or you are using SUP720, you needed miniumum 12.2(13)ZP1 or later on the CMM module as it runs its own software.
As requested by Jon , please paste the output of " Show module ".
regards,
-amit singh
01-14-2010 11:55 PM
Hi guys,
The IOS on the CMM module is wscmm-i6k9s-mz.124-3g.bin and this is the output of the show commands on 6509-E. Also you can notice, right now the CMM module is not in this chasis, it's still in the old 6509 (not 6509-E) chasis. It is not working in VSS mode also
------------------ show module ------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1337YPS4
3 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1338YSXY
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1337YJUA
6 5 Supervisor Engine 720 10GE (Hot) VS-S720-10G SAL1337YMS9
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0026.cb77.91c8 to 0026.cb77.91df 4.1 12.2(18r)S1 12.2(33)SXI2 Ok
3 0026.cbb1.1fe4 to 0026.cbb1.1ffb 4.1 12.2(18r)S1 12.2(33)SXI2 Ok
5 001f.9e2a.0ca0 to 001f.9e2a.0ca7 3.1 8.5(3) 12.2(33)SXI2 Ok
6 0021.a094.8a18 to 0021.a094.8a1f 3.1 8.5(3) 12.2(33)SXI2 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Distributed Forwarding Card WS-F6700-DFC3C SAL1338YT6X 1.4 Ok
3 Distributed Forwarding Card WS-F6700-DFC3C SAL1338YT81 1.4 Ok
5 Policy Feature Card 3 VS-F6K-PFC3C SAL1337YKTJ 1.1 Ok
5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1334X11G 2.0 Ok
6 Policy Feature Card 3 VS-F6K-PFC3C SAL1337YGDN 1.1 Ok
6 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1335XBBK 2.0 Ok
Mod Online Diag Status
---- -------------------
1 Pass
3 Pass
5 Pass
6 Pass
------------------ show power ------------------
system power redundancy mode = redundant
system power total = 3795.12 Watts (90.36 Amps @ 42V)
system power used = 1152.48 Watts (27.44 Amps @ 42V)
system power available = 2642.64 Watts (62.92 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-4000W-INT 3795.12 90.36 OK OK on
2 WS-CAC-4000W-INT 3795.12 90.36 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6509-E-FAN 150.36 3.58 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 WS-X6724-SFP 162.96 3.88 162.96 3.88 on on
3 WS-X6724-SFP 162.96 3.88 162.96 3.88 on on
5 VS-S720-10G 338.10 8.05 338.10 8.05 on on
6 VS-S720-10G 338.10 8.05 338.10 8.05 on on
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit = 10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used = 1152.48 Watts (27.44 Amps @ 42V)
system auxiliary power used = 0 Watt
01-15-2010 12:18 AM
I tried looking around and found out that you might be hitting a software bug on the CMM. Try upgrading the CMM software to
12.4.10T in the T train or to atleast 124-21 or the latest one in the mainline train.
Link to download the software for CMM :
http://www.cisco.com/public/sw-center/index.shtml
HTH,
-amit singh
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: