How to disable a route pattern in CUCM 6.1

Unanswered Question
Jan 23rd, 2010
User Badges:

How do I disable a route pattern in CUCM 6.1?


We have a route pattern in CUCM 6.1 that sends digits to a gateway and the gateway is connected to an external PBX.  I need to disable the ability to call the PBX for anyone registered to CUCM.  However I just know that in a few months management will want to turn on that ability.  I'd like to cleanly just "disable" the route pattern so we can easilty tun it back on in the future.  I want to keep it as simple as possible so I don't actually have to be there to trun it back on.


Thank you.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4.7 (3 ratings)
Loading.
Jaime Valencia Sat, 01/23/2010 - 08:01
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    2011

There is no enable/disable concept for RP (or any other DN/pattern for that matter)

Make a new partition, do not add it to any CSS and move the route pattern to that partition.


HTH


java


If this helps, please rate


www.cisco.com/go/pdihelpdesk

Tod Larson Sat, 01/23/2010 - 08:28
User Badges:

That's a good idea.  Then when we are ready we can just re-assign the route pattern to our "normal" partition/CSS.


Maybe I'll make a partition called "disabled" or "doNOTuse" so it'll clearly show that this is not to be used.

Adrian Saavedra Sat, 01/23/2010 - 09:01
User Badges:
  • Gold, 750 points or more

Hi,


Alternatively, you can block a route pattern in CallManager. Just check the option "Block this pattern".


Hope it helps,


-- Adrián.

Tod Larson Sat, 01/23/2010 - 09:45
User Badges:

That sounds like an even better idea.  I'll try that when I get to work.

Marwan ALshawi Sat, 01/23/2010 - 16:03
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Best Publication, December 2015

i think it is better to use the way that java mentioned above becuase block means this pattren

will be block for all users have acess to this pattren partition, however you may need in the future to allow some users to use it only,  in this

case you need some partitions and CSS configurations


hope this help

Tod Larson Sat, 01/23/2010 - 18:36
User Badges:

Can you point me to a tutorial on using partitions and CSS?


Right now we have partition_1 and CSS_1.  All phones are in both.


Are you saying if I add a partition_2 then I could only create a CSS_2 with both partition 1 & 2 in it?.  Then, all the phones with CSS 1 will not be able to call CSS 2...right?

Marwan ALshawi Sat, 01/23/2010 - 18:54
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Best Publication, December 2015

lets say all phone and route-patterns now they have the partition assigned to them as partition_1

and you have CC_1 that contains partition|_1 in it and assigned to all of the IP phones

now every phone can dial all other phones and the route-patterns


if you want to restrict one of the route-pattens let say pattern 12345XXX


you can do it as mentioned above by using partitions and CSS

create new partition called partition_2 assign it to this route-pattern


create new CSS called CSS_2 that contain partition_1 and partition_2

now ip phones can still dial everything except the pattern 12345XXX


if you want any IP phone to dial the above pattern as well just change the CSS of the device  d line to CSS_2


there is an other way but more advanced called line/device CSS if yo interest you may read about it using cco


good luck

if helpful Rate

Actions

This Discussion