Thank you very much for your answer markbatts

I discovered I had a problem. I saw this on the running-conf: "card type command needed for slot/vwic-slot 0/1".

So I introduced the command "card type e1 0 1". So, after that I saw "controller E1 0/1/0" on running. I was quite surprised not to see it before.

Afterwards I re-enter the commands:

   - mgcp

   - ccm-manager config server 172.17.7.5

   - ccm-manager config

I got this result:

Loading MU-GW-2801.cnf.xml from 172.17.7.5 (via FastEthernet0/0): !

[OK - 4757 bytes]

I checked the running-config and I saw these new lines:

isdn switch-type primary-5ess

no ccm-manager fax protocol cisco
ccm-manager music-on-hold

mgcp
mgcp call-agent 172.17.7.5 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
!
mgcp profile default

But when I checked on the CUCM I saw that it still appeared as "unregistered". So I selected the gateway and reset it. Doing so, I got these entries in gateway's console:

%Please configure network-clock-participate wic 1 first

%Insufficient resources to create pri-group - it has been removed

interface Serial0/1/0:15

          ^

% Invalid input detected at '^' marker.

isdn bind-l3 ccm-manager

      ^

% Invalid input detected at '^' marker.

What am I missing? I do not have any serial interface. Those commands are which you told me in your answer. Why should I have a serial interface. I am quite new in MGCP so every help is welcommed...

THANK YOU VERY MUCH

JOSU

Hi again,

I keep making some tries. The first line of the errors was:

%Please configure network-clock-participate wic 1 first

So I introduced the command "MU-GW-2801(config)#network-clock-participate wic 1". Afterwards I reset the gateway from the CUCM and I got these error:

echo-cancel coverage 8

                       ^

% Invalid input detected at '^' marker.

%At least one pri-group was configured already for E1 0/1/0

Please remove it before changing timing mode.

*Feb 10 17:35:38.979:  voice_port is not initialized

*Feb 10 17:35:39.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to down

*Feb 10 17:35:39.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:1, changed state to down

*Feb 10 17:35:39.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:2, changed state to down

*Feb 10 17:35:39.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:3, changed state to down

*Feb 10 17:35:39.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:4, changed state to down

*Feb 10 17:35:39.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:5, changed state to down

*Feb 10 17:35:39.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:6, changed state to down

*Feb 10 17:35:39.959: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:7, changed state to down

*Feb 10 17:35:39.959: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:15, changed state to down

I can see now the serial interface. But, I do not know how to solve the pri-group issue..

THANK YOU!!!

JOSU