cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1917
Views
0
Helpful
4
Replies

Router 857 ADSL performance ALICE

info
Level 1
Level 1

I have a performance problem with 2 router (model 857) with a ADSL line (Provider IT-TELECOM - Alice FLAT).

If i change router with a home one (netgear, dlink, etc..) my line goes good (at least 4MBit with speedtest.net), if I use one of my cisco it slows down to 1.5MBit.

Configuration works normally without error but slow.

Here the references of one:

Model: Cisco 857 (MPC8272) processor (revision 0x400)
Board ID: FCZ1343C479
MPC8272 CPU Rev: Part Number 0xc, Mask Number 0x10
Configuration register is 0x2102
Chassis MAC Address: 0027.0dc8.77b8
Hardware revision: 4
Board Revision: A0
P/N: 74-3502-06
Top Assy P/N: 800-26778-07
Deviation Number: 0
Fab Version: 04
CLEI Code: VAMG710DRC
FRU: CISCO857-K9
Version Identifier: V06
Processor type: 95
Chassis S/N: FCZ1343C479
Radio Country Code: FFFF
Eeprom format version: 4
PCB S/N: F0C13414W3L
Firmware: IOS 12.4(15)T10 (c850-advsecurityk9-mz.124-15.T10.bin)
CP Express: Ver 1.3

Modem: Alcatel 20190
Vendor ID:         'STMI'        'IFTN'
Vendor specific:    0x0000        0x711A
Vendor country:        0x0F        0xB5
Chip ID:        C196 (0)
DFE BOM:        DFE3.0 Annex A (1)
Capacity used:        100%    45%
Noise Margin:        28.0 dB        27.0 dB
Output Power:        16.5 dBm    12.0 dBm
Attenuation:        41.0 dB        20.5 dB
Defect status:        None        None
Last fail code:        None
Watchdog counter:    0x27
Watchdog reset:        0
Selftest result:    0x00
Subfunction:        0x00
Interrupts:        49539 (0 spurious)
PHY Access Err:        0
Activations:        7
LED Status:        ON
LED on time:        100
LED off time:        100
Init FW:        init_AMR-3.0.014_no_bist.bin
Operation FW:        AMR-3.0.014.bin
FW Source:        embedded
FW Version:        3.0.14

Any help well be appreciate.

Alessio.

4 Replies 4

paolo bevilacqua
Hall of Fame
Hall of Fame

That's a bit strange since you have high attenuation.

Anyway, try a FW upgrade from:

ftp://ftp.ciscp.com/pub/access/800

I downloaded 2 firmwares. Just a question: the last one (4.10.9) is usable for 857 routers? In the .doc file seem to be only for 836. I downloaded also 3.0.33.

Thank you in advance.

Alessio

Please try 3.0.33 first.

There are also newer versions, but need a paid support contract to access.

Alos post full router config minus passwords.

Sorry for the delay but only today i could try it.

I update the alcatel firmware but the result is the same.

I attach my configuration (without passwords)

Bye.

Alessio

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco