×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

NM-HD-2VE + 2 E1 modules clock configuration

Unanswered Question
Mar 4th, 2010
User Badges:


I want to configure clocking on a router with this configuration:


QUEEN#show inventory

NAME: "2651XM chassis", DESCR: "2651XM chassis"

PID: C2651XM-2FE       , VID: 2.0, SN: JAE08083B32


NAME: "Enhanced High Density Voice Network Module", DESCR: "Enhanced High Density Voice Network Module"

PID: NM-HD-2VE=        , VID: V  , SN: FOC08440BH5


NAME: "One port E1 voice interface daughtercard", DESCR: "One port E1 voice interface daughtercard"

PID: VWIC-1MFT-E1=     , VID: 1.0, SN: 34128133


NAME: "One port E1 voice interface daughtercard", DESCR: "One port E1 voice interface daughtercard"

PID: VWIC-1MFT-E1=     , VID: 1.0, SN: 32513251


But I have this error:


QUEEN(config)#network-clock-participate slot 1

% ERROR: "network-clock-participate slot 1" is not

% appropriate under the current router hardware configuration.



Does any one know why this error occurs?



QUEEN#show ver

Cisco IOS Software, C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.4(25b), RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Wed 12-Aug-09 10:59 by prod_rel_team


ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)


QUEEN uptime is 13 minutes

System returned to ROM by reload at 18:26:18 MSK Sun Feb 28 2010

System restarted at 18:25:42 MSK Sun Feb 28 2010

System image file is "flash:c2600-advipservicesk9-mz.124-25b.bin"



This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.


A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html


If you require further assistance please contact us by sending email to

export@cisco.com.


Cisco 2651XM (MPC860P) processor (revision 2.0) with 125986K/5086K bytes of memory.

Processor board ID JAE08083B32

M860 processor: part number 5, mask 2

2 FastEthernet interfaces

32 Serial interfaces

2 Channelized E1/PRI ports

32K bytes of NVRAM.

32768K bytes of processor board System flash (Read/Write)


Configuration register is 0x2102

Thank you.
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
William Bell Thu, 03/04/2010 - 06:26
User Badges:
  • Purple, 4500 points or more

Granted I have not messed around with a 2600 in quite some time, but I didn't see any PVDMs in your "show inventory" output.  Do you have PVDMs (carrier cards for DSP resources) installed in the router?  If not, then that may lead to the error you are seeing.


HTH.


Regards,
Bill

SludnevTN_2 Thu, 03/04/2010 - 07:15
User Badges:

As I understand PVDMs NM-HD2-VE allready has a PVDM on board (equal to PVDM2-48 ???), any I have created pri-group on each controller, and I think this means that PVDMs resources are available. Anyway thank you for yor reply

Actions

This Discussion