Solved: DSPFarm in NM-2V is "DOWN"

andrew_ho · ‎03-04-2010

Hi,

I have a 2621XM installed with NM-2V and VIC-2FXO, however, the dspfarm is always shown as "DOWN" and it doesn't allow me to use the "voice-card" command, any idea? Thanks.

Andrew

HE-VGW1#sh inventory
NAME: "2621XM chassis", DESCR: "2621XM chassis"
PID: C2621XM-2FE , VID: 3.1, SN: XXXXXXXXXX

NAME: "C2600 4 port Voice PM", DESCR: "C2600 4 port Voice PM"
PID: NM-2V= , VID: 1.1, SN: XXXXXXXX

NAME: "Two port FXO voice interface daughtercard", DESCR: "Two port FXO voice in
terface daughtercard"
PID: VIC-2FXO= , VID: 1.1, SN: XXXXXXXX

HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#sh dspfar
HE-VGW1#sh dspfarm
DSPFARM Configuration Information:
Admin State: DOWN, Oper Status: DOWN - Cause code: ADMIN_STATE_DOWN
Transcoding Sessions: 0(Avail: 0), Conferencing Sessions: 0 (Avail: 0)
Trans sessions for mixed-mode conf: 0 (Avail: 0), RTP Timeout: 600
Connection check interval 600 Codec G729 VAD: ENABLED
HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#config t
Enter configuration commands, one per line. End with CNTL/Z.
HE-VGW1(config)#voice-card 0
^
% Invalid input detected at '^' marker.

HE-VGW1(config)#

paolo bevilacqua · ‎03-08-2010

No, they can't.

Use current hardware for that.

View solution in original post

markbatts · ‎03-05-2010

I think your using the wrong commands.To access a FXO port you need to use the voice-port command.If you do a sh run you should see them, something like

voice-port 0/0/0 or similiar.

cheers

Mark

Jaime Valencia · ‎03-05-2010

I don't see any DSPs listed in the inventory, you need DSPs for voice termination or to configure DSPfarms

HTH

java

If this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

andrew_ho · ‎03-08-2010

Hi,

DSPs are present on the NM-2V, I wonder if they can be used as media resources (hardware conference bridge) for CUCM?

Thanks,

Andrew

HE-VGW1#sh voice dsp

DSP DSP                DSPWARE CURR BOOT                         PAK     TX/RX
TYPE NUM CH CODEC       VERSION STATE STATE   RST AI VOICEPORT TS ABORT PACK COUNT
==== === == ======== ========== ===== ======= === == ========= == ===== ============
C542 001 01 None         4.4.29 IDLE idle      0 0 1/0/0     NA     0    3822/4161
C542 002 01 None         4.4.29 IDLE idle      0 0 1/0/1     NA     0      594/591

paolo bevilacqua · ‎03-08-2010

No, they can't.

Use current hardware for that.