03-07-2010 10:50 PM - edited 03-15-2019 09:40 PM
Hi,
I have a CUCM 6 and a 2621XM with NM-2V and VIC-2FXO. The router is configured as a H.323 gateway as shown below. Outgoing calls from 8001 are working fine. However, incoming calls (which should all be forwarded to 8001) are not working. It keeps on ringing from the calling phone, but the actual 8001 is not ringing at all. In CUCM config, the router is defined and associated with a CSS able to reach 8001. Also attached is some debug result.
Any idea?
Thanks,
Andrew
voice-port 1/0/0
trunk-group FXOTrunkGroup
cptone AU
connection plar opx 8001
!
voice-port 1/0/1
trunk-group FXOTrunkGroup
cptone AU
connection plar 8001
!
!
!
!
!
dial-peer voice 10 pots
trunkgroup FXOTrunkGroup
destination-pattern 0[2-8]........
forward-digits all
!
dial-peer voice 100 voip
destination-pattern 8001
session target ipv4:10.8.8.80
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
#sh voice port summ
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
1/0/0 -- fxo-ls up dorm idle on-hook y
1/0/1 -- fxo-ls up dorm idle on-hook y
PWR FAILOVER PORT PSTN FAILOVER PORT
================= ==================
#sh dial-peer voice summary
dial-peer hunt 0
AD PRE PASS OUT
TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET STAT PORT
10 pots up up 0[2-8]........ 0 up trunkgroup FXOTrunkGroup
100 voip up up 8001 0 syst ipv4:10.8.8.80
#sh dialplan num 8001
Macro Exp.: 8001
VoiceOverIpPeer100
peer type = voice, information type = voice,
description = `',
tag = 100, destination-pattern = `8001',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
CLID Override RDNIS = disabled,
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 100, Admin state is up, Operation state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = enabled,
modem transport = system,
URI classes:
Incoming (Called) =
Incoming (Calling) =
Destination =
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4
type = voip, session-target = `ipv4:10.8.8.80',
technology prefix:
settle-call = disabled
ip media DSCP = ef, ip signaling DSCP = af31,
ip video rsvp-none DSCP = af41,ip video rsvp-pass DSCP = af41
ip video rsvp-fail DSCP = af41,
UDP checksum = disabled,
session-protocol = cisco, session-transport = system,
req-qos = best-effort, acc-qos = best-effort,
req-qos video = best-effort, acc-qos video = best-effort,
req-qos audio def bandwidth = 64, req-qos audio max bandwidth = 0,
req-qos video def bandwidth = 384, req-qos video max bandwidth = 0,
dtmf-relay = h245-alphanumeric,
RTP dynamic payload type values: NTE = 101
Cisco: NSE=100, fax=96, fax-ack=97, dtmf=121, fax-relay=122
CAS=123, ClearChan=125, PCM switch over u-law=0,A-law=8
G726r16 using static payload
G726r24 using static payload
RTP comfort noise payload type = 19
fax rate = voice, payload size = 20 bytes
fax protocol = system
fax-relay ecm enable
fax NSF = 0xAD0051 (default)
codec = g711ulaw, payload size = 160 bytes,
Media Setting = flow-through (global)
Expect factor = 10, Icpif = 20,
Playout Mode is set to adaptive,
Initial 60 ms, Max 250 ms
Playout-delay Minimum mode is set to default, value 40 ms
Fax nominal 300 ms
Max Redirects = 1, signaling-type = cas,
VAD = disabled, Poor QOV Trap = disabled,
Source Interface = NONE
voice class sip url = system,
voice class sip rel1xx = system,
redirect ip2ip = disabled
probe disabled,
voice class perm tag = `'
Time elapsed since last clearing of voice call statistics never
Connect Time = 4642, Charged Units = 0,
Successful Calls = 0, Failed Calls = 44, Incomplete Calls = 0
Accepted Calls = 5, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 17181509.
Matched: 8001 Digits: 4
Target: ipv4:10.8.8.80
03-10-2010 03:40 PM
Hi,
From the debug, I can see the H.225 communications between the CUCM and the gateway. The call was released with disconnect cause 1.
"H323/release_ind: Disconnect cause 1 location code 0"
According to cisco documentation, it means "Unallocated (unassigned) number. This cause indicates that the destination requested by the calling user cannot be reached because the number is unassigned. This number is not in the routing table, or it has no path across the ISDN network".
Extension 8001 is definitely working, I can call it from 8002 internally.
Any idea?
Thanks,
Andrew
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: