cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
6091
Views
0
Helpful
3
Replies

IOS Support for IP SLA

johnlloyd_13
Level 9
Level 9

hi experts,

i've got an Cisco 1841 and 2611XM series routers that doesn't support IP SLA. due to my Cisco.com login account, I can't access the Software Advisor tool to suggest the recommended IOS to support this feature. would greatly appreciate if someone could advise me the necessary IOS on both routers to support IP SLA feature. thanks in advance!

1841#sh ver
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SO
FTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 28-Nov-07 18:17 by stshen

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

SG uptime is 3 days, 16 hours, 59 minutes
System returned to ROM by power-on
System image file is "flash:c1841-ipbase-mz.124-3i.bin"

Cisco 1841 (revision 7.0) with 97280K/33792K bytes of memory.
Processor board ID FHK124628JE
2 FastEthernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
31488K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

-----------


2611#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IS-M), Version 12.3(6b), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Wed 19-May-04 23:04 by dchih
Image text-base: 0x80008098, data-base: 0x819B42DC

ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

SG uptime is 23 hours, 27 minutes
System returned to ROM by power-on
System image file is "flash:c2600-is-mz.123-6b.bin"

cisco 2611XM (MPC860P) processor (revision 0x300) with 98304K/32768K bytes of memory.
Processor board ID JAE0817EFUF (594279078)
M860 processor: part number 5, mask 2
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
1 Channelized E1/PRI port(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

2 Accepted Solutions

Accepted Solutions

Ganesh Hariharan
VIP Alumni
VIP Alumni

hi experts,

i've got an Cisco 1841 and 2611XM series routers that doesn't support IP SLA. due to my Cisco.com login account, I can't access the Software Advisor tool to suggest the recommended IOS to support this feature. would greatly appreciate if someone could advise me the necessary IOS on both routers to support IP SLA feature. thanks in advance!

1841#sh ver
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SO
FTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 28-Nov-07 18:17 by stshen

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

SG uptime is 3 days, 16 hours, 59 minutes
System returned to ROM by power-on
System image file is "flash:c1841-ipbase-mz.124-3i.bin"

Cisco 1841 (revision 7.0) with 97280K/33792K bytes of memory.
Processor board ID FHK124628JE
2 FastEthernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
31488K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

-----------


2611#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IS-M), Version 12.3(6b), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Wed 19-May-04 23:04 by dchih
Image text-base: 0x80008098, data-base: 0x819B42DC

ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

SG uptime is 23 hours, 27 minutes
System returned to ROM by power-on
System image file is "flash:c2600-is-mz.123-6b.bin"

cisco 2611XM (MPC860P) processor (revision 0x300) with 98304K/32768K bytes of memory.
Processor board ID JAE0817EFUF (594279078)
M860 processor: part number 5, mask 2
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
1 Channelized E1/PRI port(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Hi,

Following are the ios which are supported for following IP SLA commands in your routers1800 and 2600

15.0(1)M c181x-advipservicesk9-mz.15.0-1.M

12.4(11)XW10 c181x-advipservicesk9-mz.12.4-11.XW10

12.4(11)XJ4 c181x-advipservicesk9-mz.12.4-11.XJ4

12.4(24)T2 c181x-advipservicesk9-mz.12.4-24.T2

**********************************

12.4(11)XJ4 c2600-entservicesk9-mz.12.4-11.XJ4

12.4(15)T11 c2600-entservicesk9-mz.12.4-15.T11


IP SLAs - ICMP Jitter Operation
IP SLAs - ATM/Frame-Relay Thresholds
IP SLAs - Application Performance Monitor (APM)
IP SLAs - DHCP Operation
IP SLAs - DNS Operation
IP SLAs - Distribution of Statistics
IP SLAs - FTP Operation
IP SLAs - Frame Relay Interfaces
IP SLAs - Frame Relay Operation
IP SLAs - HTTP Operation
IP SLAs - History Statistics
IP SLAs - ICMP Echo Operation
IP SLAs - ICMP Path Echo Operation
IP SLAs - Multi Operation Scheduler
IP SLAs - One Way Measurement
IP SLAs - Path Jitter Operation
IP SLAs - Reaction Threshold
IP SLAs - SNA LU2 Echo
IP SLAs - SNMP Support
IP SLAs - Scheduler
IP SLAs - TCP Connect Operation
IP SLAs - UDP Based VoIP Operation
IP SLAs - UDP Echo Operation
IP SLAs - UDP Jitter Operation
IP SLAs - VoIP Threshold Traps
IP SLAs Additional Threshold Traps
IP SLAs Random Scheduler
IP SLAs Sub-millisecond Accuracy Improvements
IP SLAs VoIP Call Setup (Post Dial Delay) Monitoring

Hope to Help !!

Remember to rate the helpful post

Ganesh.H

View solution in original post

hi ganesh,

thanks! i would like to check if these IOSs can support IP SLA. i'm particular setting up IP SLA to monitor UDP jitter.

c1841-advipservicesk9-mz.124-9.T3

c1841-advipservicesk9-mz.124-9.T7

c1841-advipservicesk9-mz.124-24.T

c2600-adventerprisek9-mz.124-21a

Hi,

Following ios

c1841-advipservicesk9-mz.124-9.T3

c1841-advipservicesk9-mz.124-9.T7

c1841-advipservicesk9-mz.124-24.T

train are having Common Features in all the images that is IP SLAs - UDP Jitter Operation.

and for

c2600-adventerprisek9-mz.124-21a

IP SLAs - UDP Jitter Operation is also supported in above ios.

Hope to help !!

Ganesh.H

View solution in original post

3 Replies 3

Ganesh Hariharan
VIP Alumni
VIP Alumni

hi experts,

i've got an Cisco 1841 and 2611XM series routers that doesn't support IP SLA. due to my Cisco.com login account, I can't access the Software Advisor tool to suggest the recommended IOS to support this feature. would greatly appreciate if someone could advise me the necessary IOS on both routers to support IP SLA feature. thanks in advance!

1841#sh ver
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SO
FTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 28-Nov-07 18:17 by stshen

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

SG uptime is 3 days, 16 hours, 59 minutes
System returned to ROM by power-on
System image file is "flash:c1841-ipbase-mz.124-3i.bin"

Cisco 1841 (revision 7.0) with 97280K/33792K bytes of memory.
Processor board ID FHK124628JE
2 FastEthernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
31488K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

-----------


2611#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IS-M), Version 12.3(6b), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Wed 19-May-04 23:04 by dchih
Image text-base: 0x80008098, data-base: 0x819B42DC

ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

SG uptime is 23 hours, 27 minutes
System returned to ROM by power-on
System image file is "flash:c2600-is-mz.123-6b.bin"

cisco 2611XM (MPC860P) processor (revision 0x300) with 98304K/32768K bytes of memory.
Processor board ID JAE0817EFUF (594279078)
M860 processor: part number 5, mask 2
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
1 Channelized E1/PRI port(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Hi,

Following are the ios which are supported for following IP SLA commands in your routers1800 and 2600

15.0(1)M c181x-advipservicesk9-mz.15.0-1.M

12.4(11)XW10 c181x-advipservicesk9-mz.12.4-11.XW10

12.4(11)XJ4 c181x-advipservicesk9-mz.12.4-11.XJ4

12.4(24)T2 c181x-advipservicesk9-mz.12.4-24.T2

**********************************

12.4(11)XJ4 c2600-entservicesk9-mz.12.4-11.XJ4

12.4(15)T11 c2600-entservicesk9-mz.12.4-15.T11


IP SLAs - ICMP Jitter Operation
IP SLAs - ATM/Frame-Relay Thresholds
IP SLAs - Application Performance Monitor (APM)
IP SLAs - DHCP Operation
IP SLAs - DNS Operation
IP SLAs - Distribution of Statistics
IP SLAs - FTP Operation
IP SLAs - Frame Relay Interfaces
IP SLAs - Frame Relay Operation
IP SLAs - HTTP Operation
IP SLAs - History Statistics
IP SLAs - ICMP Echo Operation
IP SLAs - ICMP Path Echo Operation
IP SLAs - Multi Operation Scheduler
IP SLAs - One Way Measurement
IP SLAs - Path Jitter Operation
IP SLAs - Reaction Threshold
IP SLAs - SNA LU2 Echo
IP SLAs - SNMP Support
IP SLAs - Scheduler
IP SLAs - TCP Connect Operation
IP SLAs - UDP Based VoIP Operation
IP SLAs - UDP Echo Operation
IP SLAs - UDP Jitter Operation
IP SLAs - VoIP Threshold Traps
IP SLAs Additional Threshold Traps
IP SLAs Random Scheduler
IP SLAs Sub-millisecond Accuracy Improvements
IP SLAs VoIP Call Setup (Post Dial Delay) Monitoring

Hope to Help !!

Remember to rate the helpful post

Ganesh.H

hi ganesh,

thanks! i would like to check if these IOSs can support IP SLA. i'm particular setting up IP SLA to monitor UDP jitter.

c1841-advipservicesk9-mz.124-9.T3

c1841-advipservicesk9-mz.124-9.T7

c1841-advipservicesk9-mz.124-24.T

c2600-adventerprisek9-mz.124-21a

hi ganesh,

thanks! i would like to check if these IOSs can support IP SLA. i'm particular setting up IP SLA to monitor UDP jitter.

c1841-advipservicesk9-mz.124-9.T3

c1841-advipservicesk9-mz.124-9.T7

c1841-advipservicesk9-mz.124-24.T

c2600-adventerprisek9-mz.124-21a

Hi,

Following ios

c1841-advipservicesk9-mz.124-9.T3

c1841-advipservicesk9-mz.124-9.T7

c1841-advipservicesk9-mz.124-24.T

train are having Common Features in all the images that is IP SLAs - UDP Jitter Operation.

and for

c2600-adventerprisek9-mz.124-21a

IP SLAs - UDP Jitter Operation is also supported in above ios.

Hope to help !!

Ganesh.H

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco