connecting T1 from PBX to 2800 router running CME

Answered Question
Mar 16th, 2010
User Badges:

I have T1 provided by the Telecom group to connect to Call Manager express,


Can i connect to a FXO card  or Wic T1 card


i have following hardware on the router



2 FastEthernet interfaces

1 Serial interface

2 Serial(sync/async) interfaces

1 terminal line

1 Virtual Private Network (VPN) Module

2 Voice FXO interfaces

2 Voice FXS interfaces

1 cisco service engine(s)



Thanks

Sri

Correct Answer by Aaron Harrison about 7 years 2 months ago

Hi


Nope, you can connect a T1 to a T1. Not an FXO (a completely different technology) or a WIC (they don't support voice).


It has to be a voice T1 (i.e. for a 2800 series this would normally be a VWIC-1MFT-T1/E1 or VWIC2-1MFT-T1/E1 or the 2-port versions of these).


You also need DSPs - at least 24 channels, so a PVDM2-32 should cover the T1 and the four analog ports you have (unless you need more for transcoding, G729 calls, etc..).


Regards


Aaron


Please rate helpful posts..

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
Aaron Harrison Tue, 03/16/2010 - 11:36
User Badges:
  • Super Bronze, 10000 points or more
  • Community Spotlight Award,

    Member's Choice, May 2015

Hi


Nope, you can connect a T1 to a T1. Not an FXO (a completely different technology) or a WIC (they don't support voice).


It has to be a voice T1 (i.e. for a 2800 series this would normally be a VWIC-1MFT-T1/E1 or VWIC2-1MFT-T1/E1 or the 2-port versions of these).


You also need DSPs - at least 24 channels, so a PVDM2-32 should cover the T1 and the four analog ports you have (unless you need more for transcoding, G729 calls, etc..).


Regards


Aaron


Please rate helpful posts..

banalas_2 Tue, 03/16/2010 - 12:33
User Badges:

i have UC520  with the following configuration


will it be possible to connect




Cisco UC520-8U-4FXO-K9 (MPC8358) processor (revision 0x202) with 249856K/12288K bytes of m

emory.

Processor board ID FHK133975NA

MPC8358 CPU Rev: Part Number 0x804A, Revision ID 0x20

14 User Licenses

10 FastEthernet interfaces

2 terminal lines

4 Voice FXO interfaces

4 Voice FXS interfaces

1 Voice MoH interface

1 cisco service engine(s)

128K bytes of non-volatile configuration memory.

125440K bytes of ATA CompactFlash (Read/Write)


Configuration register is 0x2102


REMoteCCME#sh ds

REMoteCCME#sh dspfarm

DSPFARM Configuration Information:

Admin State: DOWN, Oper Status: DOWN - Cause code: ADMIN_STATE_DOWN

Transcoding Sessions: 0(Avail: 0), Conferencing Sessions: 0 (Avail: 0)

Trans sessions for mixed-mode conf: 0 (Avail: 0), RTP Timeout: 600

Connection check interval 600 Codec G729 VAD: ENABLED





Thanks

Sri

Aaron Harrison Tue, 03/16/2010 - 12:37
User Badges:
  • Super Bronze, 10000 points or more
  • Community Spotlight Award,

    Member's Choice, May 2015

Hi


I thought you had a 2800...???


As I understand it the UC series are fixed config, so no T1, no connection...


Aaron


Please rate helpful posts..

banalas_2 Tue, 03/16/2010 - 12:46
User Badges:

Yes, i have both 2800 and UC520



Thanks for your help

Actions

This Discussion