03-19-2010 12:35 AM - edited 03-04-2019 07:51 AM
Dear Gurus,
I have 2 7206 with PA-POS-OC3SMI configure back to back, i have the interface up/up but i cannot ping the ip address with increaseing CRC. Below is my basic config.
7206-A
interface POS3/0
ip address 10.10.3.41 255.255.255.252
no keepalive
clock source internal
no cdp enable
end
7206-B
interface POS1/0
ip address 10.10.3.42 255.255.255.252
no keepalive
no cdp enable
end
TIA.
03-19-2010 03:43 AM
Hello Jepoy,
I suspect the two PA are using a different CRC or one has scrambing enabled compare the output of
sh int pos
on both devices
crc can be crc16 or crc32 ; scrambling can be enabled or disabled.
or PA are different or they have different default settings in different IOS images
Edit:
also enable keepalive to be able to detect cabling errors
Hope to help
Giuseppe
03-19-2010 05:32 AM
Hi Guiseppe,
Thanks for the tips again, here's the output of my interfaces. Still i've hard encoded crc and enable keepalives, still the port is up but i cant even ping the local ip address on the pos.
7206-B#sh interfaces pos 1/0
POS1/0 is up, line protocol is up
Hardware is Packet over Sonet
Internet address is 10.10.3.42/30
MTU 3000 bytes, BW 155000 Kbit, DLY 100 usec,
reliability 152/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 32, loopback not set
Keepalive set (10 secs)
Scramble enabled
Last input 00:00:00, output 02:38:03, output hang never
Last clearing of "show interface" counters 09:06:32
Input queue: 0/900/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/1500/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 116250 kilobits/sec
5 minute input rate 189000 bits/sec, 22 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
1123707 packets input, 2073838413 bytes, 0 no buffer
Received 426371 broadcasts, 0 runts, 19874647 giants, 0 throttles
0 parity
71076982 input errors, 19932579 CRC, 0 frame, 31269756 overrun, 0 ignored,
0 abort
1397 packets output, 35288 bytes, 0 underruns
0 output errors, 0 applique, 6 interface resets
0 output buffer failures, 0 output buffers swapped out
6 carrier transitions
7206-A#sh interfaces pos 3/0
POS3/0 is up, line protocol is up
Hardware is Packet over Sonet
Description:
Internet address is 10.10.3.41/30
MTU 3000 bytes, BW 155000 Kbit, DLY 100 usec,
reliability 146/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 32, loopback not set
Keepalive set (10 secs)
Scramble enabled
Last input 02:39:04, output 02:37:48, output hang never
Last clearing of "show interface" counters never
Input queue: 0/900/0/0 (size/max/drops/flushes); Total output drops: 1
Queueing strategy: weighted fair
Output queue: 0/1000/1500/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 116250 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
994783 packets input, 4038877857 bytes, 0 no buffer
Received 947212 broadcasts, 2 runts, 780917 giants, 0 throttles
0 parity
2696244 input errors, 712031 CRC, 0 frame, 1203294 overrun, 0 ignored, 0 ab
ort
1609 packets output, 42456 bytes, 0 underruns
0 output errors, 0 applique, 13 interface resets
0 output buffer failures, 0 output buffers swapped out
22 carrier transitions
03-19-2010 06:11 AM
Hello Jepoy,
I don't understand:
how is it possible to have an interface up/up with keepalive set when:
>> Last input 00:00:00, output 02:38:03, output hang never
>> Last input 02:39:04, output 02:37:48, output hang never
second interface should be up/down if keepalive is set.
I would try to reset the interface with
int pos3/0
shut
controller pos3/0
shut
and then unshut
you can also use enc ppp to take advantage of more advanced PPP debug ouput
Hope to help
Giuseppe
03-19-2010 06:26 AM
HI Guissepe,
The interface are down now, here's the full config and output.
7206-B#sh run interface pos 1/0
Building configuration...
Current configuration : 269 bytes
!
interface POS1/0
ip address 10.10.3.42 255.255.255.252
load-interval 30
crc 32
pos framing sdh
no pos report slos
no pos report slof
no pos report plop
no pos report sf-ber
no pos report b1-tca
no pos report b2-tca
no pos report b3-tca
no cdp enable
end
POS1/0 is up, line protocol is down
Hardware is Packet over Sonet
Internet address is 10.10.3.42/30
MTU 4470 bytes, BW 155000 Kbit, DLY 100 usec,
reliability 165/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 32, loopback not set
Keepalive set (10 sec)
Scramble disabled
Last input 00:00:00, output 00:00:47, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 277000 bits/sec, 8 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
37642 packets input, 110066984 bytes, 0 no buffer
Received 30006 broadcasts, 0 runts, 998465 giants, 0 throttles
0 parity
9002107 input errors, 920843 CRC, 0 frame, 7082799 overrun, 0 ignored, 0 ab
ort
30 packets output, 1120 bytes, 0 underruns
0 output errors, 0 applique, 6 interface resets
0 output buffer failures, 0 output buffers swapped out
7206-A#sh run in pos 3/0
Building configuration...
Current configuration : 337 bytes
!
interface POS3/0
description :To LAOAG MPLS
ip address 10.10.3.41 255.255.255.252
no ip proxy-arp
load-interval 30
crc 32
clock source internal
pos framing sdh
no pos report slos
no pos report slof
no pos report plop
no pos report sf-ber
no pos report b1-tca
no pos report b2-tca
no pos report b3-tca
no cdp enable
end
#sh int pos 3/0
POS3/0 is up, line protocol is down
Hardware is Packet over Sonet
Description: :To LAOAG MPLS
Internet address is 10.10.3.41/30
MTU 4470 bytes, BW 155000 Kbit, DLY 100 usec,
reliability 128/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 32, loopback not set
Keepalive set (10 sec)
Scramble disabled
Last input 00:01:46, output 00:01:28, output hang never
Last clearing of "show interface" counters 00:30:18
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 0 bits/sec, 0 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
11279 packets input, 25728325 bytes, 0 no buffer
Received 5763 broadcasts, 3 runts, 157481 giants, 0 throttles
0 parity
1077673 input errors, 207716 CRC, 0 frame, 712473 overrun, 0 ignored, 0 abo
rt
38 packets output, 2192 bytes, 0 underruns
0 output errors, 0 applique, 5 interface resets
0 output buffer failures, 0 output buffers swapped out
3 carrier transitions
03-20-2010 05:14 AM
Hello Jepoy,
another thought:
being the two PA single mode, the signal may be too strong causing loss of frame delineation.
in this case the addition of a 5dB or 10DB in line attenuator could be a solution.
you can check this with
sh controller pos 3/0
see
http://www.fiberattenuator.com/
A way to build a home made attenuator is to wrap fiber cable over a pen to make strict curves but this can cause fiber damage
Hope to help
Giuseppe
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide