03-22-2010 03:39 AM - edited 03-04-2019 07:53 AM
Dear all,
Fighting during late 2 days with 2811 router. It doesnt recognize inserted 4ESW HWIC module.
IOS version should support this hardware.
Please take a look at routers output.
*Mar 22 09:51:16: %SYS-5-RELOAD: Reload requested by admin on console. Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.
Initializing memory for ECC
.
c2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0x3117470
Self decompressing the image : ## [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0003E7 0X00474800 C2811 Mainboard
0X00264050 Onboard VPN
0X000021B8 Onboard USB
0004F4 0X00016804 Virtual Private Network (VPN) Module
0X002C29F0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X00BC4BFC
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 12Mb.
Using 4 percent iomem. [12Mb/256Mb]
Restricted Rights Legend
---------------------------------------------------------OMITTED
Installed image archive
Cisco 2811 (revision 49.46) with 249856K/12288K bytes of memory.
Processor board ID FHK********
2 FastEthernet interfaces
2 Virtual Private Network (VPN) Modules
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Press RETURN to get started!
*Mar 22 09:53:19.447: %GT96K_FEWAN-1-UNKNOWN_WIC: slot 0, wic card has an unknown id 64
hostname#sh ver
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T10, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 14-Sep-09 14:01 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
hostname uptime is 31 minutes
System returned to ROM by reload at 09:51:16 UTC Mon Mar 22 2010
System image file is "flash:c2800nm-advipservicesk9-mz.124-15.T10.bin"
---------------------------------------------------------OMITTED
Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.
Processor board ID FHK1344F40Q
2 FastEthernet interfaces
2 Virtual Private Network (VPN) Modules
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
hostname##sh inv
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V07 , SN: FHK1344F40Q
NAME: "Virtual Private Network (VPN) Module on Slot 0", DESCR: "Encryption AIM Element"
PID: AIM-VPN/SSL-2 , VID: V01, SN: FOC13394XRE
Card was normally recognized by other router
03-22-2010 12:53 PM
It looks like you should open a TAC case.
Hope it helps.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide