How to get Licence MAC to MCS server?

Answered Question
Apr 13th, 2010

Best regards.

To download L-CM-DL, I need the "License MAC"

To find address I did the following step:
1. Log in to the Cisco UCM command line interface (CLI) and enter show status.

But in this devices the "show status" comando not exist.

The MCS have 3 Mac address, 2 Giga ethernet and 1 Service-Engine interface,

Which I can use to download the license or which command can I use to see the License MAC.

Thank for help me.

I have this problem too.
0 votes
Correct Answer by htluo about 6 years 6 months ago

On your particular version (6.1.2), you use command "show network eth0 detail" to get the MAC address:

admin:show network eth0 detail
Ethernet 0
DHCP         : disabled           Status     : up
IP Address   : 10.88.7.221        IP Mask    : 255.255.255.000
Link Detected: yes                Mode       : Auto disabled, Full, 1000 Mbits/s
Duplicate IP : no
Queue Length : 1000               MTU        : 1500
MAC Address  : 00:0c:29:8a:7e:49
RX stats:
  bytes   :   3219412021   packets :     15179215   errors :           43
  dropped :            0   overrun :            0   mcast  :            0
TX stats:
  bytes   :   1267274831   packets :      9269296   errors :            0
  dropped :            0   carrier :            0   colsns :            0

Michael

http://htluo.blogspot.com

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4 (2 ratings)
Loading.
Aaron Harrison Tue, 04/13/2010 - 14:39

Hi

It sounds like you are looking at a Cisco ISR or other router - not an MCS server.

Can you do a 'show version' on this device?

Aaron

JOSE CHAUCA Tue, 04/13/2010 - 14:50

Yes, the output of show version command is:

Cisco IOS Software, 3800 Software (C3825-ADVIPSERVICESK9-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 10-Jan-08 18:20 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T10, RELEASE SOFTWARE (fc1)

RO-GPA-01 uptime is 7 weeks, 5 days, 19 hours, 12 minutes
System returned to ROM by power-on
System restarted at 20:06:54 UTC Fri Jan 15 2010
System image file is "flash:c3825-advipservicesk9-mz.124-9.T7.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

Cisco 3825 (revision 1.2) with 484352K/39936K bytes of memory.
Processor board ID FTX1236A0YP
2 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
28 Voice FXO interfaces
4 Voice FXS interfaces
1 cisco service engine(s)
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
125440K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

Aaron Harrison Tue, 04/13/2010 - 15:05

Hi

OK - so when you are registering CallManager DLUs, you register these to your publisher MAC address. The publisher (and all other MCS servers) is a HP or IBM based server.

What you have is a router, which can be used as a telephony system if you configure CallManager Express on it.

You can't install DLUs on a router; and you don't need them.

Do you have an actual MCS server and CallManager software?

Aaron

JOSE CHAUCA Thu, 05/27/2010 - 11:31

Hi Aaron.

I have a MCS server 7828-I3

But the output of show status command is:

admin:show status

Host Name    : CM7828
Date         : Thu May 27, 2010 13:28:52
Time Zone    : America/Guayaquil
Locale       : en_US.UTF-8
Product Ver  : 6.1.2.1000-13
Platform Ver : 2.0.0.1-1

Uptime:
13:28:53  up 9 days, 18:04,  1 user,  load average: 0.22, 0.40, 0.47

CPU Idle:  89.90%  System:  01.01%    User:  02.02%
  IOWAIT:  05.56%     IRQ:  00.00%    Soft:  01.52%   Intr/sec: 440.40

Memory Total:        6156852K
        Free:          28744K
        Used:        6128108K
      Cached:        3084140K
      Shared:              0K
     Buffers:         127584K

                        Total            Free            Used
Disk/active         43264144K       36138388K        6686220K (16%)
Disk/inactive       43264176K       41033656K          32828K (1%)
Disk/logging       150538756K      122603092K       20288728K (15%)


admin:

I have not publisher MAC Addrees.

Which command I can use to get the MAC

Thanks.

Jose

Correct Answer
htluo Thu, 05/27/2010 - 12:15

On your particular version (6.1.2), you use command "show network eth0 detail" to get the MAC address:

admin:show network eth0 detail
Ethernet 0
DHCP         : disabled           Status     : up
IP Address   : 10.88.7.221        IP Mask    : 255.255.255.000
Link Detected: yes                Mode       : Auto disabled, Full, 1000 Mbits/s
Duplicate IP : no
Queue Length : 1000               MTU        : 1500
MAC Address  : 00:0c:29:8a:7e:49
RX stats:
  bytes   :   3219412021   packets :     15179215   errors :           43
  dropped :            0   overrun :            0   mcast  :            0
TX stats:
  bytes   :   1267274831   packets :      9269296   errors :            0
  dropped :            0   carrier :            0   colsns :            0

Michael

http://htluo.blogspot.com

Actions

This Discussion