redistribute static and default-information not found in 1941 router

Unanswered Question
Apr 15th, 2010
User Badges:

I want to inject default route into BGP to allow remote sites to learn the route but when configuring the 1941 router, I am not able to see both command when I perform show ? command.


I am still able to enter these commands into the config but all remote sites are not able to see the default route when I perform show ip bgp and show ip route.



The imageis 15.1 base version.  May I know how I can resolve this issue or any alternate solution to advertise default route in BGP?

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Jon Marshall Thu, 04/15/2010 - 09:32
User Badges:
  • Super Blue, 32500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 LAN, WAN

tohchinlam wrote:


I want to inject default route into BGP to allow remote sites to learn the route but when configuring the 1941 router, I am not able to see both command when I perform show ? command.


I am still able to enter these commands into the config but all remote sites are not able to see the default route when I perform show ip bgp and show ip route.



The imageis 15.1 base version.  May I know how I can resolve this issue or any alternate solution to advertise default route in BGP?


Have you tried -


ip route 0.0.0.0 0.0.0.0 Null0


router bgp

network 0.0.0.0 mask 0.0.0.0


Edit - the above assumes that the BGP router will have better routes to destinations and if it doesn't that you want to discard the traffic. If the BGP router should forward traffic on to another router then just change the "ip route 0.0.0.0 0.0.0.0 Null0" statement to "ip route 0.0.0.0 0.0.0.0 ".


Jon

tohchinlam Thu, 04/15/2010 - 18:17
User Badges:

Hi,



No. I have not yet tried these commands. May I know will there be any impact as this is a live network and would like to minimize any disruption?



Thanks

Chin Lam

tohchinlam Thu, 04/15/2010 - 18:33
User Badges:

I have a default route that pointed to the firewall. By placing ip route

0.0.0.0 0.0.0.0 Null0, will it drops all the internet traffics?

Jerry Ye Thu, 04/15/2010 - 18:53
User Badges:
  • Cisco Employee,

If you have a default route pointed to the FW, then you don't have to  configure the ip route 0.0.0.0 0.0.0.0 null0. You should be able to  advertise the default like Jon said in the previous post with the network command in the BGP process.


HTH,

jerry

Jon Marshall Fri, 04/16/2010 - 01:10
User Badges:
  • Super Blue, 32500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 LAN, WAN

Jerry


Thanks for this, the last thing i want is to take down the network


As Jerry and i said if you have a default-route there already then leave as is and simply add this under your BGP config -


router bgp

network 0.0.0.0 mask 0.0.0.0


As for whether it will affect your network, well i'm not sure how routing is working at the moment if you don't have a default-route being propogated to any EBGP peers. It won't reload or reset any devices if that is what you mean but only you know how it will affect your own network.


Jon

Richard Burts Fri, 04/16/2010 - 10:05
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 LAN, WAN

The original poster describes that he wants a default route in BGP so the remote neighbors will learn a default route and could not find the default route command in BGP. It is not found directly under BGP but is a parameter on the BGP neighbor command:

router bgp 1

neighbor 1.1.1.1 default-originate


HTH


Rick

Actions

This Discussion