04-15-2010 07:06 PM - edited 03-15-2019 10:18 PM
I've now experienced this issue with 12.4.24T and 12.4.24T3 on multiple Cisco 2811's. We configure the following MGCP like this:
mgcp
mgcp call-agent 10.10.10.10 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode nse
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
mgcp default-package fxr-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 ecm
mgcp fax t38 ls_redundancy 2
mgcp fax t38 hs_redundancy 2
mgcp fax-relay ans-disable
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface Vlan2
mgcp bind media source-interface Vlan2
After a reboot, T.38 is always disabled:
mgcp
mgcp call-agent 10.10.10.10 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode nse
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
mgcp default-package mt-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 ecm
mgcp fax t38 inhibit
mgcp fax t38 ls_redundancy 2
mgcp fax t38 hs_redundancy 2
mgcp fax-relay ans-disable
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface Vlan2
mgcp bind media source-interface Vlan2
Any idea how to fix this and keep T.38 enabled across reloads? Is this a bug?
Solved! Go to Solution.
04-16-2010 07:49 AM
Ho Jordan,
I think you are hitting this bug;
MGCP fax T38 inhibit and ecm configured upon reload | |
Symptom: On a Cisco MGCP gateway registered to Cisco Unified Callmanager server, running IOS 124-24T we have enabled T38. But after a reload following command lines are seen in the configuration and all T38 faxes fail: mgcp fax t38 ecm mgcp fax t38 inhibit Conditions: Specific to MGCP T38 fax. The command "ccm-manager config" needs to be enabled to cause this issue. Debug capture during boot up will show: 000386: Jun 18 21:58:06.588: cmapp_xml_cfg_router: configuring [mgcp fax t38 inhibit] Workaround: This issue is not seen in Cisco IOS images 124-15T9 and 124-20T3. You can also manually configure this after the reload: mgcp default-package fxr-package (if need be) no mgcp fax t38 inhibit no mgcp fax t38 ecm and then reset the gateway from the Callmanager | Status Fixed Severity 3 - moderate Last Modified In Last 2 weeks Product Cisco IOS software Technology 1st Found-In 12.4(24)T 12.4(24.6)T9 Known Affected Versions Fixed-In 12.4(24)MD 12.4(24)T2 15.1(0.7)T 15.1(0.2)PI12f 15.0(1)M0.5 15.1(24.6.12)PIL13 12.4(22)T4 15.1(1)XB 15.1(0.2.7)PIB13 15.1(1.5.1)PIA13 15.1(0.0.10)PIL14 |
Cheers!
Rob
Please support CSC Helps Haiti
04-16-2010 07:49 AM
Ho Jordan,
I think you are hitting this bug;
MGCP fax T38 inhibit and ecm configured upon reload | |
Symptom: On a Cisco MGCP gateway registered to Cisco Unified Callmanager server, running IOS 124-24T we have enabled T38. But after a reload following command lines are seen in the configuration and all T38 faxes fail: mgcp fax t38 ecm mgcp fax t38 inhibit Conditions: Specific to MGCP T38 fax. The command "ccm-manager config" needs to be enabled to cause this issue. Debug capture during boot up will show: 000386: Jun 18 21:58:06.588: cmapp_xml_cfg_router: configuring [mgcp fax t38 inhibit] Workaround: This issue is not seen in Cisco IOS images 124-15T9 and 124-20T3. You can also manually configure this after the reload: mgcp default-package fxr-package (if need be) no mgcp fax t38 inhibit no mgcp fax t38 ecm and then reset the gateway from the Callmanager | Status Fixed Severity 3 - moderate Last Modified In Last 2 weeks Product Cisco IOS software Technology 1st Found-In 12.4(24)T 12.4(24.6)T9 Known Affected Versions Fixed-In 12.4(24)MD 12.4(24)T2 15.1(0.7)T 15.1(0.2)PI12f 15.0(1)M0.5 15.1(24.6.12)PIL13 12.4(22)T4 15.1(1)XB 15.1(0.2.7)PIB13 15.1(1.5.1)PIA13 15.1(0.0.10)PIL14 |
Cheers!
Rob
Please support CSC Helps Haiti
09-01-2011 10:04 AM
Hi,
I have the exact same problem with 2900 and 3900 using 15.1(3)T, 15.1(3)T2 and 15.1(4)M1 releases.
I use "ccm-manager config" to download the MGCP configuration from CUCM 6.1.5 and each time I reload or a enter "no ccm config, ccm config" to force the download, all the mgcp config is reset to default.
Before the reload:
mgcp call-agent XXXXXXXXXXXXX service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
mgcp default-package fxr-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax rate 14400
mgcp fax t38 nsf 000000
no mgcp fax-relay sg3-to-g3
mgcp rtp payload-type g726r16 static
After the reload:
mgcp call-agent XXXXXXXXXXXXX service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
mgcp default-package mt-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax rate 14400
mgcp fax t38 inhibit
mgcp fax t38 nsf 000000
no mgcp fax-relay sg3-to-g3
mgcp rtp payload-type g726r16 static
The problem is that I use now 2900 and 3900 ISR G2 routers, and the version 15.x is the minimum.
For the other routers (~10) I dont have problem because I use the 12.4(20)T3 and the config is well saved.
I will try older IOS versions but I would appreciate if someone can advice me directly.
Thank you for your help.
Yorick
09-01-2011 10:38 AM
09-01-2011 11:05 AM
Hi Rob,
Unfortunately, I cannot find it in the Download center.
I can only access to 15S, 15M, 15T and Special and Early, but no one contains a XB release .
Do you think I have to open a case to get it?
I am afraid now because I am pretty sure I have several customers with ISR G2, configured for T.38 on C2900 and C3900. If they reload the routers, no more faxes...
How is it possible a so severe problem is present in so many versions?
Maybe it is related to the version of our CUCM as well (6.1.5)?
I will do some tests tomorrow morning in a customer site owning a 2911 and using T.38 with CUCM 7.1.5.
Thank you for your help.
Yorick
09-01-2011 11:34 AM
Hi Yorick,
I think a TAC case is an excellent idea. I'm guessing they can find a more current
IOS version that contains the fix for this and set it up for you as a special
download. You should not have to deal with this issue every time the router re-loads.
Cheers!
Rob
09-06-2011 12:54 AM
Hi Rob,
For your information, a case is opened to troubleshoot this problem, I still don't get a satisfying answer but in the sametime I compared the same test with different CUCM version.
It seems that the problem only occurs with CUCM 6.1.x. I think it's because the CUCM 7.x and 8.x contain more MGCP parameters (t.38 package, and so on). MGCP config from CUCM webpages is very (too) basic in 6.x and I think in IOS 15.x some parameters are defaulting to a certain value when the parameter does not come populated from the CUCM.
I will post the update as soon as it will be resolved.
Yorick
07-20-2012 01:15 AM
We've suffered with this problem for a number of years, across 2800s & 2900s; both CUCM versions 6 & 7; a range of IOS versions including 12.4T, 15.1 and 15.2.
Our latest incarnation is a 2951 running 15.2(3)T and CUCM 7.1.5.
It's sad to think that it's never been adequately solved!
Thanks, Steve
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: