CCM6 and MGCP gateway :Called number not seen with "show voice call statu" command

Unanswered Question
Apr 20th, 2010
User Badges:

Hi,

I've configured a CCM with a voice gatway that use E1 PRI.

CCM use SIP and MGCP to make outbound call through the voice gateway.

I will use MGCP at the end. The SIP is just for temporary test.


Question : How to display the called numbe when the E1 port is managed by MGCP?


1/ If I use SIP I can see the called number when I do the show voice call status command

2/ If I use MGCP,then I cannot see the called number when using this same command.


I'm using the voice call status for troubleshooting



DescriptionCallIDCallIDccVdbPortDSP/ChCalled #Codec Dial-peers
SIP call0x979B733C50x483A9C400/2/0:15.230/6:1*033140599g711ulaw0/51
MGCP call0x979D211E20x483AB6800/3/0:15.310/3:6*        g711ulaw0/0
SIP call0x97AEB362B0x483A9C400/2/0:15.210/6:6*0320413446g711ulaw0/51


Is there any solution?

Or I have to see the CDR? But its result is not instantly

Best regards,


Antra

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Ayodeji Okanlawon Tue, 04/20/2010 - 06:28
User Badges:
  • Super Bronze, 10000 points or more
  • Cisco Designated VIP,

    2017 IP Telephony

Hi,


Have you tried "show isdn active"

iantra123 Tue, 04/20/2010 - 06:37
User Badges:

I've tried, but it just show the calls that use SIP calls  :

All calls that display star and nothing after are calls made from MGCP


rtVg00#sh voice call status
CallID     CID  ccVdb      Port        DSP/Ch  Called #   Codec    Dial-peers
0x9880F    FB3  0x483A9C40 0/2/0:15.25 0/5:1  *0320418297 g711ulaw  0/51
0x98ABB    12ED 0x483AB680 0/3/0:15.27 0/3:5  *           g711ulaw  0/0
0x98ADA    13E2 0x483A9C40 0/2/0:15.27 0/6:6  *0320262734 g711ulaw  0/51
0x98AE7    12F8 0x483AB680 0/3/0:15.31 0/3:1  *           g711ulaw  0/0
0x98AEB    12F9 0x483AB680 0/3/0:15.30 0/3:3  *           g711ulaw  0/0
0x98AEF    12FA 0x483AB680 0/3/0:15.25 0/6:2  *           g711ulaw  0/0
0x98AF7    12FC 0x483AB680 0/3/0:15.28 0/6:5  *           g711ulaw  0/0
0x98AFA    1412 0x483A9C40 0/2/0:15.22 0/4:4  *0320263654 g711ulaw  0/51
0x98B02    141E 0x483A9C40 0/2/0:15.26 0/5:3  *0331184452 g711ulaw  0/51
0x98B26    1454 0x483A9C40 0/2/0:15.21 0/4:5  *0327615059 g711ulaw  0/51
0x98B43    130F 0x483AB680 0/3/0:15.24 0/4:1  *           g711ulaw  0/0
0x98B57    1314 0x483AB680 0/3/0:15.22 0/6:4  *           g711ulaw  0/0
0x98B7A    14D2 0x483A9C40 0/2/0:15.31 0/3:2  *0320267304 g711ulaw  0/51
13 active calls found

ORArtVg00#show isdn active    
--------------------------------------------------------------------------------
                                ISDN ACTIVE CALLS
--------------------------------------------------------------------------------
Call    Calling      Called       Remote  Seconds Seconds Seconds Charges
Type    Number       Number       Name    Used    Left    Idle    Units/Currency
--------------------------------------------------------------------------------
Out       90017  0320262734                    90 Unavail   -          0       
Out       90218  0331184452                    69 Unavail   -          0       
Out       90016  0320263654                    63 Unavail   -          0       
Out       90045  0327615059                    35 Unavail   -          0       
--------------------------------------------------------------------------------

rtVg00#

Ayodeji Okanlawon Tue, 04/20/2010 - 07:16
User Badges:
  • Super Bronze, 10000 points or more
  • Cisco Designated VIP,

    2017 IP Telephony

Then you need to run a "debug isdn q931" and be sure you can see the Calling and called number from the MGCP gateway.

iantra123 Tue, 04/20/2010 - 07:08
User Badges:

This appers in the show isdn status


rtVg00#sh isdn status
Global ISDN Switchtype = primary-net5

%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply

ISDN Serial0/2/1:15 interface
        dsl 0, interface ISDN Switchtype = primary-net5
        L2 Protocol = Q.921 0x0000  L3 Protocol(s) = CCM MANAGER 0x0003
    Layer 1 Status:
        ACTIVE
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask:  0xFFFF7FFF
    Number of L2 Discards = 0, L2 Session ID = 5




==============

This is the config in the controllers :


controller E1 0/2/1
framing NO-CRC4
clock source internal
pri-group timeslots 1-31 service mgcp
description Test E1 PRI



interface Serial0/2/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!

================

Actions

This Discussion