cisco 1941 and hwic-8a configuration

Unanswered Question
Apr 26th, 2010

hi.

we have old test equipment that has to be configurated using vt-420 terminal.

we used to have cisco AS2511-rj device we use to connect those devices, so that ip-address,port 2001 did go to test device 1 and ip-address, port 2002 did go to test device 2.

after we moved to other building that ancient AS2511-rj did not work anymore.

so we ordered 1941 with HWIC-8a which was recommended to us to replace that old device.

but how should we configure this ?

I did  not found anything from cisco support pages or from google search?

there is no modem between 1941 and test devices, we just want to connect rj-45 to our devices, like we did with old AS2511.

should we use loopback and do like in http://www.cisco.com/en/US/tech/tk801/tk36/technologies_configuration_example09186a008014f8e7.shtml

how should we configure those async interfaces ?

and how is those port numbering connected to async lines ?

is P0 2000 or 2001 ?

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
shailesh.h Mon, 04/26/2010 - 09:06

Hope you have physically installed the card in the router. Kindly share the output of

  1. sh ver (this will show whether u r card is detected or not)
  2. sh running-conf (this will show you the interface details like slot / interface no etc)

Connector types and other misc information is provided in

http://www.cisco.com/en/US/prod/collateral/modules/ps5949/datasheet_c78-491363.html

Asynchronous Serial Task List : To configure an asynchronous interface so you can connect to an asynchronous device on the network, complete the following tasks:

•Specify an Asynchronous Serial Interface

•Configure Asynchronous Serial Encapsulation

•Configure Dedicated or Interactive Mode

•Enable Routing on the Asynchronous Interface

•Configure Group and Member Asynchronous Interfaces

http://www.cisco.com/en/US/docs/ios/11_2/configfun/configuration/guide/1cintrfc.html#wp2580

jakkamikko Tue, 04/27/2010 - 03:02

cisco#sh ver

Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M1, REL

EASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Wed 02-Dec-09 14:14 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M3, RELEASE SOFTWARE (fc1)

and
cisco#show running-config
Building configuration...
Current configuration : 5649 bytes
!
! Last configuration change at 11:06:08 UTC Mon Apr 26 2010
!
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname cisco
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 xxxxxxxxxxxxxxxx
enable password 7 xxxxxxxxxxxxxx
!
no aaa new-model
!
no ipv6 cef
no ip source-route
no ip gratuitous-arps
ip cef
!
!
!
!
no ip bootp server
ip domain name yourdomain.com
multilink bundle-name authenticated
!
!
crypto pki trustpoint TP-self-signed-1193908939
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1193908939
revocation-check none
rsakeypair TP-self-signed-1193908939
!
!
crypto pki certificate chain TP-self-signed-1193908939
certificate self-signed 01
 
  yyy
        quit
license udi pid xxxxx
!
!
username xxxxxxxxxxxxx
username xxxxxxxxxxxx
!
!
!
!
!
!
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$$ES_LAN$
ip address aa.aa.aa.74 255.255.255.0
duplex auto
speed auto
no mop enabled
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Async0/0/0
no ip address
encapsulation slip
!
interface Async0/0/1
no ip address
encapsulation slip
!
interface Async0/0/2
no ip address
encapsulation slip
!
interface Async0/0/3
no ip address
encapsulation slip
!
interface Async0/0/4
no ip address
encapsulation slip
!
interface Async0/0/5
no ip address
encapsulation slip
!
interface Async0/0/6
no ip address
encapsulation slip
!
interface Async0/0/7
no ip address
encapsulation slip
!
ip forward-protocol nd
!
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip route 0.0.0.0 0.0.0.0 aa.aa.aa.1
!
access-list 23 permit 10.10.10.0 0.0.0.7
dialer-list 1 protocol ip permit
!
no cdp run
!
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------
^C
banner login ^C
-----------------------------------------------------------------------
-----------------------------------------------------------------------
^C
banner motd ^C
^C
!
line con 0
login local
line aux 0
line 0/0/0 0/0/7
line vty 0
privilege level 15
password 7 xxxxxxxxxxx
login
transport input all
line vty 1 4
privilege level 15
password 7 xxxxxxxxxxxx
login
transport input telnet ssh
line vty 5 15
privilege level 15
password 7 xxxxxxxxxxxxxx
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
end
cisco#
Question is how should I connect those async lines?
using loopback?
or like old AS2511 ?
in there there was no loopback (if old paper copy of running-config is right)
does anyone have similar configuration where I could see basic principle of connecting those lines?
also is port number automatically set?

Actions

This Discussion