Frederico, thanks for the reply.  I tried those, no joy.  I continue to get destination host unreachable when pinging out or in, I get nothing in either logs to show it is getting to either device.  I'm still trying, but not sure what to try from here.

Tunnel is stable, still connected.  I can post any of the config if it will help.

TIA

gene

Gene,

Let's do the following:

Please post the output of:

sh cry isa sa

sh cry ips sa

From the ASA

Those commands should tell us if the tunnel is established and if traffic is passing through.

Federico.

Result of the command: "sh cry isa sa"

   Active SA: 1
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1

1   IKE Peer: 67.60.168.34
    Type    : L2L             Role    : initiator
    Rekey   : no              State   : MM_ACTIVE

Result of the command: "sh cry ips sa"

interface: CableOne
    Crypto map tag: CableOne_map, seq num: 1, local addr: 24.116.132.42

      access-list CableOne_1_cryptomap permit ip 172.16.100.0 255.255.252.0 FriscoCenter 255.255.255.0
      local ident (addr/mask/prot/port): (172.16.100.0/255.255.252.0/0/0)
      remote ident (addr/mask/prot/port): (FriscoCenter/255.255.255.0/0/0)
      current_peer: 67.60.168.34

      #pkts encaps: 99, #pkts encrypt: 99, #pkts digest: 99
      #pkts decaps: 9, #pkts decrypt: 9, #pkts verify: 9
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 99, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 24.116.132.42, remote crypto endpt.: 67.60.168.34

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 10F0CC1C

    inbound esp sas:
      spi: 0x32C3D2C6 (851694278)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 1, }
         slot: 0, conn_id: 13172736, crypto-map: CableOne_map
         sa timing: remaining key lifetime (kB/sec): (3914999/28635)
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x000003FF
    outbound esp sas:
      spi: 0x10F0CC1C (284216348)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 1, }
         slot: 0, conn_id: 13172736, crypto-map: CableOne_map
         sa timing: remaining key lifetime (kB/sec): (3914994/28635)
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001

Thanks

The tunnel is up and working.
I see packets flowing through the tunnel between the local LAN behind the ASA 172.16.100.0/22 and a remote network called FriscoCenter

Try the following:
Enable the command: management-access inside
Try to PING from the ASA to the remote side by doing: ping inside x.x.x.x (where x.x.x.x is an IP on the FriscoCenter)

Make sure that both LANs have a route to the remote network pointing to the VPN device.

Federico.