05-05-2010 03:08 PM - edited 03-15-2019 10:38 PM
I am running into an issue where i cannot receive incoming calls when Incoming called party number is missing.
Other calls are successful. I have a NEC PBX sending calls to my Cisco 2821 doing NI2 network side on my side.
Is there any command that would block incoming callled number?
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077064: *May 5 21:05:58.150: ISDN Se0/1/1:23 Q931: RX <- SETUP pd = 8 callref = 0x0200
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077065: <TAB>Bearer Capability i = 0x9090A2
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077066: <TAB><TAB>Standard = CCITT
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077067: <TAB><TAB>Transfer Capability = 3.1kHz Audio
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077068: <TAB><TAB>Transfer Mode = Circuit
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077069: <TAB><TAB>Transfer Rate = 64 kbit/s
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077070: <TAB>Channel ID i = 0xA98385
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077071: <TAB><TAB>Exclusive, Channel 5
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077072: <TAB>Progress Ind i = 0x8181 - Call not end-to-end ISDN, may have in-band info
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077073: <TAB>Called Party Number i = 0x80, '7795'
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077074: <TAB><TAB>Plan:Unknown, Type:Unknown
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077075: *May 5 21:05:58.166: ISDN Se0/1/1:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8200
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077076: <TAB>Channel ID i = 0xA98385
05-05-2010 13:58:33 Local7.Debug 10.1.11.248 5077077: <TAB><TAB>Exclusive, Channel 5
05-05-2010 13:58:34 Local7.Debug 10.1.11.248 5077078: *May 5 21:05:58.378: ISDN Se0/1/1:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x8200
05-05-2010 13:58:34 Local7.Debug 10.1.11.248 5077079: <TAB>Cause i = 0x82AF - Resource unavailable, unspecified
05-05-2010 13:58:34 Local7.Debug 10.1.11.248 5077080: *May 5 21:05:58.470: ISDN Se0/1/1:23 Q931: RX <- RELEASE pd = 8 callref = 0x0200
05-05-2010 13:58:34 Local7.Debug 10.1.11.248 5077081: <TAB>Cause i = 0x8190 - Normal call clearing
05-05-2010 03:12 PM
Can you please post and compare a clean trace of a succesful call to the same number ?
Because, iit's not normal that cisco fails to process anon. calls, normally it just doesn't care about.
05-05-2010 03:16 PM
05-05-2010 03:24 PM
In your trace, the only failed call is for a number for which no succesful call is shown anywhere.
.
Again: cisco doesn't care about calling number unless you so configure, so that is not your issue.
05-05-2010 03:30 PM
If that is not my issue how come the cisco is sending the disconnect?
05-05-2010 03:31 PM
Also i can call that number from my PBX over the Cisco 2821 to the NEC.
05-05-2010 03:37 PM
Here is an example of a call going to that extension on the NEC. This call completed just fine.
2010-05-05 15:31:27 Local7.Info 10.1.11.248 5081427: *May 5 22:38:52.789: %ISDN-6-CONNECT: Interface Serial0/1/0:22 is now connected to 16304687538 N/A
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081428: *May 5 22:38:52.869: ISDN Se0/0/1:23 Q931: Applying typeplan for sw-type 0xD is 0x2 0x1, Calling num 5095357613
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081429: *May 5 22:38:52.869: ISDN Se0/0/1:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Called num 6282
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081430: *May 5 22:38:52.869: ISDN Se0/0/1:23 Q931: TX -> SETUP pd = 8 callref = 0x041D
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081431: Bearer Capability i = 0x8090A2
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081432: Standard = CCITT
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081433: Transfer Capability = Speech
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081434: Transfer Mode = Circuit
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081435: Transfer Rate = 64 kbit/s
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081436: Channel ID i = 0xA98383
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081437: Exclusive, Channel 3
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081438: Display i = 'zzcicsvc'
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081439: Calling Party Number i = 0x2180, '5095357613'
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081440: Plan:ISDN, Type:National
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081441: Called Party Number i = 0x80, '6282'
2010-05-05 15:31:27 Local7.Debug 10.1.11.248 5081442: Plan:Unknown, Type:Unknown
2010-05-05 15:31:28 Local7.Debug 10.1.11.248 5081443: *May 5 22:38:53.025: ISDN Se0/0/1:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x841D
2010-05-05 15:31:28 Local7.Debug 10.1.11.248 5081444: Channel ID i = 0xA98383
2010-05-05 15:31:28 Local7.Debug 10.1.11.248 5081445: Exclusive, Channel 3
2010-05-05 15:31:28 Local7.Debug 10.1.11.248 5081446: *May 5 22:38:53.041: ISDN Se0/0/1:23 Q931: RX <- ALERTING pd = 8 callref = 0x841D
05-05-2010 03:42 PM
Are you using H.323 or MGCP ?
Please post only clean traces, these above a difficult to read.
And clarify all and any systme connected and how exactly.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide