C2960 image support for SNMPv3 and transport output ssh

amardram123 · ‎05-06-2010

Hi All.

Which version of image on c2960 switch support snmpV3 and Transport output ssh commands?

Currently we are running c2960-lanbase-mz.122-35.SE5.bin.

Need urgent help...

Regards
Amar

Nael Mohammad · ‎05-06-2010

Using the Cisco Feature Navigator, you can download 12.2(53)SE1 with the CAT2960 platform with LAN BASE that supports both SSH and SNMPv3.

http://www.cisco.com/cgi-bin/Software/SWSearch/SWSearch_results.cgi/SWSearch.txt?isChild=false&file_delimiter=contains&search=Search&searchPhrase=c2960-lanbasek9-mz.122-53.SE1.bin

c2960-lanbasek9-mz.122-53.SE1.bin

madhusudhan s · ‎05-06-2010

Hi Neal,

I am Amar colleague, His query is if transport output ssh is supported on any of c2960-48-ttl switch?

Regatrds

Madhu

jyotiraj_Majumdar · ‎05-06-2010

Hi,

You can used mentioned flash for 2960 and try ("flash:c2960-lanbasek9-mz.122-52.SE.bin")

Thanks

Jyoti

Ganesh Hariharan · ‎05-06-2010

Hi All.

Which version of image on c2960 switch support snmpV3 and Transport output ssh commands?

Currently we are running c2960-lanbase-mz.122-35.SE5.bin.

Need urgent help...

Regards
Amar

Hi Amar,

Even your current ios supports snmpv3 and ssh

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

madhusudhan s · ‎05-06-2010

Hi ganesh

I am Amar Colleague, We tried, Transport output SSH is not supported on c2960-lanbase-mz.122-35.SE5.bin.

Regrads

Amar

Ganesh Hariharan · ‎05-06-2010

Hi ganesh

I am Amar Colleague, We tried, Transport output SSH is not supported on c2960-lanbase-mz.122-35.SE5.bin.

Regrads

Amar

Amar,

Can you try tansport output all, is it working for ssh or not and snmp v3 should work with this image.

Ganesh.H

Nael Mohammad · ‎05-07-2010

To enable transport out ssh, ensure you are in config mode using "line vty 0 4" and then type "transport input ssh" and "transport output ssh" . To enable snmp on the c2960, you need to be in config mode.

Enabling SNMPv1/v2c on Cisco IOS devices:

To enable SNMPv1/v2c on Cisco IOS devices, follow these steps:

snmp-server community ro

snmp-server community r

Enabling SNMPv3 on Cisco IOS devices:

1. enable

2. configure terminal

3. snmp-server group [groupname {v1 | v2c | v3 [auth | noauth | priv]}] [read readview] [write writeview] [notify notifyview] [access access-list]

4. exit

5. show snmp group

This is for 12.4 but the cli syntax is the same:

http://www.cisco.com/en/US/partner/docs/ios/netmgmt/configuration/guide/nm_cfg_snmp_sup_ps6441_TSD_Products_Configuration_Guide_Chapter.html#wp1201017

glen.grant · ‎05-07-2010

His version may support it but his version is not a crypto code version so it will not work . Imagename must have a K9 in it.