05-11-2010 05:53 AM - edited 03-06-2019 11:01 AM
Hi,
we are using the cisco CAT 6500 in our network
one of power unit is failed we replaced with the new one but after installing its powered on but not in the redunant mode
DIST65-01.TC2#sh power redundancy-mode
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
error log it says
*May 10 23:52:53.524 BST: %C6KPWR-SP-4-PSOK: power supply 2 turned on.
*May 10 23:52:53.528 BST: %C6KPWR-SP-4-PSREDUNDANTMISMATCH: power supplies rated outputs do not match.
DIST65-01.TC2#sh power status power-supply 1
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-2500W 2331.00 55.50 OK OK on
DIST65-01.TC2#sh power status power-supply 2
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
2 unknown 1153.32 27.46 ?? ?? on
DIST65-01.TC2#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICES_WAN-M), Version 12.2(33)SXI3, RELEASE SOFTWARE (fc2)
And also we see in module status that :
DIST65-01.TC2# sh module
Mod Ports Card Type Model
--- ----- -------------------------------------- ------------------ -----------
1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE
2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX
3 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX
4 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC
5 2 Supervisor Engine 720 (Active) WS-SUP720-BASE
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0022.55bd.1ee0 to 0022.55bd.1ee3 2.7 12.2(14r)S5 12.2(33)SXI3 Ok
2 000d.29da.ae88 to 000d.29da.aeb7 3.0 7.2(1) 12.2(33)SXI3 Ok
3 0011.20b8.79b8 to 0011.20b8.79e7 6.0 7.2(1) 12.2(33)SXI3 Ok
4 0013.1a44.74f0 to 0013.1a44.74f7 3.1 5.4(2) 12.2(33)SXI3 Ok
5 0013.c320.a6dc to 0013.c320.a6df 3.5 8.4(2) 12.2(33)SXI3 Ok
Mod Sub-Module Model Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Distributed Forwarding Card WS-F6700-DFC3B 4.6 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 2.7 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
4 Pass
5 Pass
can i know what it means of WS-SUP720-BASE module ?
thanks
Vinu
05-11-2010 06:01 AM
Vinu,
can i know what it means of WS-SUP720-BASE module ?
That is the Sup720 base, then you add PFC and MSFC to it see:
5 Policy Feature Card 3 WS-F6K-PFC3B 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 2.7 Ok
HTH
Reza
05-11-2010 07:33 AM
Hi
Any help on the power redunancy issue
is this because of Powerunit or someother issue
thanks in advance
On Tue, May 11, 2010 at 2:01 PM, sharifimr <
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide