05-12-2010 04:05 AM - edited 03-06-2019 11:02 AM
Hi
i'm tring to enable jumbo frames between 3560E (Access) & 6509E (Core)
for 6509E jumbo frames support MTU size
(config)#system jumbomtu ?
<1500-9216> Jumbo mtu size in Bytes, default is 9216
for 3560E jumbo frames support MTU size
(config)#system mtu jumbo ?
<1500-9198> Jumbo MTU size in bytes
i need help to know what is the jumbo fram size supported ?
shall i use (9216) or (9198) or what exactly.
thanks
05-12-2010 04:23 AM
What is the line card on the 6500 connected to the C3560e switch. "show module".
05-12-2010 04:34 AM
On the 3560E, the system MTU range is from 1500 to 9198 bytes. The max is 9198 byte. Use the "system mtu jumbo" globally to change it.
On the 6500 the following switching modules do not support Jumbo frame. When jumbo frame support is configured, these modules drop ingress frames larger than 8092 bytes
• WS-X6516-GE-TX when operating at 100 Mbps
• WS-X6148-RJ-45, WS-X6148-RJ-45V and WS-X6148-RJ21, WS-X6148-RJ21V
• WS-X6248-RJ-45 and WS-X6248-TEL
• WS-X6248A-RJ-45 and WS-X6248A-TEL •
WS-X6348-RJ-45, WS-X6348-RJ45V and WS-X6348-RJ-21, WX-X6348-RJ21V, WS-X6548-GE-TX, WS-X6548V-GE-TX, WS-X6148-GE-TX, and WS- X6148V-GE-TX "
post "show module" to identify what card you have on the Cat 6500.
Francisco.
WS-X67xx cards does support Jumbo frame up to 9000 bytes. Max is 9216 bytes per frame
Francisco
05-12-2010 12:22 PM
hi
3560E is connected using WS-X6724-SFP
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
4 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G
7 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Distributed Forwarding Card WS-F6700-DFC3C
2 Distributed Forwarding Card WS-F6700-DFC3C
4 Distributed Forwarding Card WS-F6700-DFC3C
5 Policy Feature Card 3 VS-F6K-PFC3C
5 MSFC3 Daughterboard VS-F6K-MSFC3
7 Distributed Forwarding Card WS-F6700-DFC3C
05-13-2010 04:38 AM
On the 3560E, you can set system MTU range between 1500 to 9198 bytes by use the "system mtu jumbo" command.
On the 6500 the WS-X6724-SFP line card the maximum frame size is 9216 bytes.
Hope to help..
Francisco
05-12-2010 10:37 PM
Hi
i'm tring to enable jumbo frames between 3560E (Access) & 6509E (Core)
for 6509E jumbo frames support MTU size
(config)#system jumbomtu ?
<1500-9216> Jumbo mtu size in Bytes, default is 9216for 3560E jumbo frames support MTU size
(config)#system mtu jumbo ?
<1500-9198> Jumbo MTU size in bytesi need help to know what is the jumbo fram size supported ?
shall i use (9216) or (9198) or what exactly.
thanks
Hi,
The default MTU size is 9216 bytes after you enable jumbo frame support on the individual port for 6500 series switches and for 3560 switches All Gigabit Ethernet interfaces support jumbo frames up to 9000 bytes.
Check out the below link for more information on Jumbo frame configuration on switches
Hope to Help !!
Ganesh.H
Remember to rate the helpful post
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: