Unable to select individual devices in RME 4.3.1. Why would this be happening?

Unanswered Question
May 13th, 2010

Hi all,

Another problem has surfaced with RME:

In RME NetConfig Jobs it would seem that selecting individual devices is a problem.

The "All devices" tick box can be selected, however the individual selections under it they are not available.

Screenshots below

top selection.jpg

Any ideas for a solution?  What logs are required?individual selections.jpg

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Joe Clarke Thu, 05/13/2010 - 08:20

Post the NetconfigClient.log as well as the NMSROOT/MDC/tomcat/logs/stdout.log and stderr.log after loading the Netconfig device selector.

Russell Bovaird Sun, 05/16/2010 - 17:30


please find attached the files as requested.

I have also noticed that even though the selection of the group of devices is allowed, if you keep going with the top selection, and error CFG0007 is produced.

Joe Clarke Sun, 05/16/2010 - 21:36

Post the list of files under NMSROOT/MDC/tomcat/webapps/rme/WEB-INF/lib/pkg and NMSROOT/www/classpath/com/cisco/nm/xms/psu/pkgs/rme.

Joe Clarke Mon, 05/17/2010 - 14:47

Yep, it looks like a package map problem.  Post the NMSROOT/www/classpath/com/cisco/nm/xms/psu/maps/rme* files.  That said, if these maps are bad, you will need to contact TAC to get the procedure to regenerate the maps.  Your package repository looks okay at a quick glance, but it may not hurt to get TAC to send you an up-to-date set of RME packages as well.

Russell Bovaird Mon, 05/17/2010 - 16:48


have attached the image of the directory requested.

I'll contact the TAC for the procedure to regenerate the maps (as well as get the new ones) if you still think that this is the path to take after seeing the picture above.

Thanks again for your responses.


Joe Clarke Tue, 05/18/2010 - 09:40

Your package maps are corrupt.  You will need to get the steps from TAC to fix them.  That should take care of your Netconfig problem.

Russell Bovaird Tue, 05/18/2010 - 16:14

Thanks Joe.

I'll open a TAC case for the corrupt files.

For my knowledge:

     Were the files attached corrupted?

     How did you know? - ie what part was corrupt?

Thanks for all your assistance.


Joe Clarke Tue, 05/18/2010 - 16:30

Yes, the attached files are corrupt.  If you look at the device map, the corruption should be very obvious.  Many of the lines are spliced, truncated, out of alignment, etc.

Russell Bovaird Tue, 06/01/2010 - 16:10

Hi Joe,

sorry it's taken so long to reply.

TAC were able to help and suggested that I run the following 2 commands which I did:


set NMSROOT=%CWMIBDIR%\..\..\..

%NMSROOT%\lib\jre\bin\java -classpath %NMSROOT%\lib\jre\lib;%NMSROOT%\lib\classpath;%NMSROOT%\objects\log4j\1.1.3\log4j.jar;%NMSROOT%\MDC\tomcat\shared\lib\MICE.jar;%NMSROOT%\MDC\tomcat\shared\lib\NATIVE.jar;%NMSROOT%\MDC\tomcat\shared\lib\jdom.jar;%NMSROOT%\www\classpath;%NMSROOT%\lib\classpath\servlet.jar;%NMSROOT%\MDC\tomcat\webapps\cwhp\WEB-INF\classes com.cisco.nm.xms.psu.packagemgmt.map.CreateMaps %NMSROOT%\www\classpath\com\cisco\nm\xms\psu\pkgs\rme


This has rectified this problem and https://supportforums.cisco.com/thread/2016907 problem.

Thanks again for your help


w.kuhn Thu, 10/28/2010 - 17:53

Hi Russel,

I have the same problem and running the commands you provided, I'm getting log4j:error. Any ideas?

Joe Clarke Thu, 10/28/2010 - 17:55

This is not a problem.  The log4j message is expected.  The command looks to be running correctly.

w.kuhn Thu, 10/28/2010 - 18:01

Thanks Joseph,

But it still did not fix my problem. Do I need to restart services?



Joe Clarke Thu, 10/28/2010 - 18:06

Yes, you should have done this with Daemon Manager shutdown.  I recommend you start a new thread detailing the problems you're seeing and what you've done thus far to fix them.


This Discussion

Related Content