PVC on Cisco 867 Router Setup

Unanswered Question
May 17th, 2010
User Badges:

Hi,


I'm try to setup a Cisco 867 using two PVC. So what I need is one ATM interface, and two virtual ATM's, ATM0.1 and ATM0.2. And als two Dialers. Can anyone help me with the command order to achief my goal?


I have found several config layouts (show run), but I'm not able to setup using the CLI. How to setup a virtual ATM? Do I need to create the ATM0.1 first before I can assing any PVC's or will it be created automaticly?


I'm able to setup the general ATM interface:


# config term

(config)# interface atm 0

(config)# ip address x.x.x.x


Do I need to confige ATM0.1 on the ATM interface? Please help!

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Ganesh Hariharan Mon, 05/17/2010 - 05:10
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Member's Choice, February 2016

Hi,


I'm try to setup a Cisco 867 using two PVC. So what I need is one ATM interface, and two virtual ATM's, ATM0.1 and ATM0.2. And als two Dialers. Can anyone help me with the command order to achief my goal?


I have found several config layouts (show run), but I'm not able to setup using the CLI. How to setup a virtual ATM? Do I need to create the ATM0.1 first before I can assing any PVC's or will it be created automaticly?


I'm able to setup the general ATM interface:


# config term

(config)# interface atm 0

(config)# ip address x.x.x.x


Do I need to confige ATM0.1 on the ATM interface? Please help!

Check out the below link for PVC configuration on Cisco 860,880 and 890 series


http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/software/configuration/guide/pppoanatfm.html


Hope to Help !!


Ganesh.H

Tim Roelands Tue, 05/18/2010 - 01:25
User Badges:

Hi Ganesh,


Create reference guide! Thanks. One problem left (could not find it in te reference). The reference guide explaines a lot of (ATM) interface tuning, my problem is (I came down from GUI interface management to CLI)  I don't know how to create an additional ATM interface! ATM interface ATM0 does exist, but what I need are additional interface like ATM0.1 and ATM0.2. Tuning those interfaces isn't the problem, I just can't enter them, because they don't exist Thanks in advance!

paolo bevilacqua Tue, 05/18/2010 - 07:32
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Just configure them and they will exist.

Tim Roelands Tue, 05/18/2010 - 12:40
User Badges:

But to configure, I have first enter the interface do I? Just like configuring the ATM interface:


# config term

(config)# interface ATM0

(config-if)# then configure, but I can't when they do not exist...

paolo bevilacqua Tue, 05/18/2010 - 12:47
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Name them and they will exist. Call it black magic !?!

Tim Roelands Wed, 05/19/2010 - 00:30
User Badges:

And it did! Thanks! used to following:


#config term

(config)# int atm0.2 point-to-point

(config)# pvc 0/1

(config)#


Then it worked, needed to add the point-to-point name!

Actions

This Discussion